Search the forum,

Recent content by Marty1979

  1. M

    40 year trainee plumber looking for work in South East London/Kent and Surrey

    Good afternoon I am seeking part time work on Thursdays and Fridays in the above locations if possible please. I have had previous experience on the tools and have recently paid for and completed my City and Guilds 6129 diploma in plumbing and heating. I have all my own tools and a csr to...
  2. M

    Help! Vaillant boiler not working after changing out a radiator

    Thanks mate, so when the heating kicks in it will raise the bar pressure higher. So do you think that'll be OK on the radiators etc? Once raised to 1.5 bar cold do I need to bleed the rads?
  3. M

    Help! Vaillant boiler not working after changing out a radiator

    Hello guys. Please can you help as at wits end. I've changed out 4 radiators over the last 12 months in my house and the last one being yesterday. I now have a F75 code and a S98 information code on my vaillaint Pro eco tec 28 combi boiler. I had a GSR installer friend come over and he bled...
  4. M

    Request for work shadowing please - SE London, Kent and Surrey

    Good evening I am looking for a work shadowing opportunity with a view to work alongside an experienced plumber/heating engineer such as yourself on a part time basis from July 2019. In the meantime, I would like to be able to enhance my plumbing skills and confidence so I would be very...
  5. M

    Request for work shadowing in South East and Kent

    Good I am looking for a work shadowing opportunity with a view to work alongside an experienced plumber/heating engineer on a part time basis from July 2019. In the meantime, I would like to be able to enhance my plumbing skills and confidence so I would be very grateful if you would consider...
  6. M

    Using existing copper M10 tails for push fit connection

    Thanks ShaunCorbs just don't fancy disturbing the compression joints and all the other stuff in the way. I think I can use my pipe slice to cut and leave enough of the 15mm end of the copper tails before they taper off. Just wanted to make sure that the tails are 15mm all the way until it goes...
  7. M

    Using existing copper M10 tails for push fit connection

    Hi all Is it possible to cut existing M10 copper tails feeding existing monobloc tap at the 15mm section and then connect push fit M10 tap flexies? Reason I ask is that the original M10 copper tails are eminating from two compression 15mm isolation valves with a lot of other pipework in the...
  8. M

    Running 21.5mm condense pipe into 110mm soil pipe question

    Hi Rob, if the condense pipe doesn't have a trap on the boiler what are the potential consequences? Thanks mate
  9. M

    Running 21.5mm condense pipe into 110mm soil pipe question

    No not gas safe but common sense prevails and says you wouldn't want to run to outside because of freezing temps. Basically the condense pipe runs through unaccessible roof on mum's extension and condense pipe was tapped into the 40mm bath waste pipe (also in the unaccessible roof space of...
  10. M

    Running 21.5mm condense pipe into 110mm soil pipe question

    Thanks very much all and yes Shaun mate it is definitely internal to avoid freezing conditions.
  11. M

    Running 21.5mm condense pipe into 110mm soil pipe question

    Hi folks. Is it OK for me to run 21.5mm boiler condense pipe into strap boss for 110mm upvc? No smells should come back in I'm assuming? Any suggestions where to buy adapters? Ideally all solvent weld as will be internal of property. Thanks very much
Creating content since 2001. Untold Media.

OFFICIAL SPONSORS

OFFICIAL SPONSORS

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock