Search the forum,

Chrome Elbow Fittings

Discuss Chrome Elbow Fittings in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
A

antsals

Good Afternoon,
I'm after a little help. I installed a new radiator; one of these designer stainless steel ones. The 15mm tapping comes out of the bottom of the rad; so I purchased two chrome 15mm male to female so I could mount the trv.

The problem is the fittings on the 15mm males side have a o-ring to seal. I PTFE taped the thread about 10 wraps. When I tighten in its not at the 90 degree angle to my valve. What is the best way to acheive a good seal but make sure its tight enough that it doesn't move when knocked?

Cheers
Ant
 
ae235.jpg

This is what they gave me at the plumbers merchants.....any better ideas?

Cheers
Ant
 
where did you put ptfe? o-ring should go to the radiator but dont put anything else on the thread. shouldnt be any problem with it unless your pipes are not straight. never done these but should be ok :)
 
I put the ptfe tape around thread below the o-ring. The problem is it would be ok but when tightened up to nip up against the o-ring the elbow isn't at 90 degrees online with the radiator. If I slacken off to get it correct it's not solid enough?

Any ideas?
 
it should make proper seal, that what is made for. unless there was some original fitting supplied with your radiator. whats the gap like when tightened. i just think maybe the thread is not long enough. is radiator supported to the wall properly? there is also chance you have cross threaded the fitting and now is not screwing back properly. sorry, i was just trying to post all possible options i could think off now..
 
Last edited:
Remove the O ring, put plenty of PTFE tape around the fitting, the tape will not only seal the thread but also make a gasket as the O ring should.
10 times is probably not enough.
The threads are probably parallel threads instead of tapered threads as with most radiator connections.
 
My explanation was not great I guess and I've been meaning to re-post but never got around to it.

Input above great but what seems to happen is when I screw into the rad, the I rotate say 3 / 4 times at the point the 'o' ring engages / starts squeezing I'm past the point where I need to be to tap into the valve. If I back it off to correct position it just feels really slack. If someone knocked it ie hoover.....I wouldnt want to know what it would do!

Attached is a picture of an example of how I am using it to tap into the central heating.

alternate-option-pipes-thru-wall-(7)[1].jpg



Also the face the oring seals into isn't flat, it is slightly concaved. What am I best doing?

Ant
 
I have borrowed some loctite 577 from a pipe fitter. He said put all round the thread screw it in until you are at required angle then leave it 24 to 48 hours. He said it will be solid and won't leak. Does this sound like a plan?

When you had problem do you just load it up with ptfe tape screw onto correct angle and just leave it? Does it feel loose?

Cheers,
Ant
 
antsals said:
I have borrowed some loctite 577 from a pipe fitter. He said put all round the thread screw it in until you are at required angle then leave it 24 to 48 hours. He said it will be solid and won't leak. Does this sound like a plan?

When you had problem do you just load it up with ptfe tape screw onto correct angle and just leave it? Does it feel loose?

Cheers,
Ant
Click to expand...

Only sounds good if it a good tight fit if loose it won't work
 
Locktight 55 about 7 to 15 turns then a dollop of jet blue for good measure. Don't keep ptfe in van our shops or stores. Lock tight all the way.

When you roll it on go anticlockwise? So when you thred it in to rad it isn't pushed back. Start one or two threads in and build a nice bulge about 2/3 along nut with locktight.
 
I originally used an angle trv but it does stick out too much and I prefer the trv being vertical jut looks better.
So you recon that even if I don't get the fitting tight the loctite 55 and blue jet will seal it? What about it being loose that can't be good?

Thanks
Ant
 
Zebedy,
Are you serious about winding the locktite on anti-clockwise.
i would have thought that would undo the locktite when winding it into the fitting.
Unless of course its a left hand thread
 
Always wind the tape around the thread (or Olive) so the tail (end) of the tape goes the same way as the nut tightens.
Easy to get it wrong when working upside down though!
 
Put a question mark next to it, do it without thinking so couldn't remember, tried to visualise but no joy! Your right clockwise!
 
Zebedy de gas said:
Locktight 55 about 7 to 15 turns then a dollop of jet blue for good measure. Don't keep ptfe in van our shops or stores. Lock tight all the way.

When you roll it on go anticlockwise? So when you thred it in to rad it isn't pushed back. Start one or two threads in and build a nice bulge about 2/3 along nut with locktight.
Click to expand...

Anticlockwise just pushes it all off no seal !!
 
Status
Not open for further replies.

Reply to Chrome Elbow Fittings in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

dreikher
Hole in copper pipe, solder under floor, T coupling & protection
I was stupid enough not to check the position of the pipes under the tiles when installing a toilet and drilled right through the center of a 16 mm copper water pipe. I exposed the pipe by removing a ~30cm section of the plastic sleeve and a ~10 cm section of the pipe around the hole. Several...
Replies
0
Views
117
dreikher
dreikher
P
LCS to new water mains
Hi, I have an old steel water mains pipe (approx 45mm) that I need to connect to a new pehd water mains (25mm). I can't get at it to create a new thread so what's the best way of connecting the two? Cheers, Peter
Replies
2
Views
159
ShaunCorbs
ShaunCorbs
C
Mixer bar fitting solutions?
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
0
Views
109
ChrisGid
C
P
Repeated Airlock in Bathroom
Hi, Can anyone advise as to why the cold water to my bathroom keeps airlocking? This originally happened about 12 months ago and has happened 3-4 times since. It’s an upstairs bathroom, fed from a tank in the attic. The tank is about 8 Meters away and feeds a bath, sink and toilet. The tank...
Replies
9
Views
255
Chuck
C
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock