You are using an out of date browser. It may not display this or other websites correctly. You should upgrade or use an alternative browser.
inserts
A threaded insert, also known as a threaded bushing, is a fastener element that is inserted into an object to add a threaded hole. They may be used to repair a stripped threaded hole, provide a durable threaded hole in a soft material, place a thread on a material too thin to accept it, mold or cast threads into a work piece thereby eliminating a machining operation, or simplify changeover from unified to metric threads or vice versa.
quality product wanted, my 1/4 turn kitchen sink tap inserts need replacing and i am looking for ones with a spindle gland nut, rather than a circlip which previous experiance says won't last five minutes. as the circlip either weakens or wears out.
none of the ironmongery supermarkets appear...
I have Honeywell Valencia TRVs 10mm pipe size, I’m making mods to accommodate larger rads and it looks like the 10mm compression insert is special to Honeywell as all available inserts are 15mm to 10mm which do not fit as the compression nut has a 10mm hole, not a 15mm.
Anyone know if you can...
The use of inserts on 10mm rolls of plastic covered copper. Brass inserts are available for this purpose, but does anyone use them. They have an O/D of 7.7mm where as the I/D of all of the coils available to me are 8.6 min.
Hi all
The other day a pipe had burst in the bathroom under the floorboards due to one of the caps (not sure of the actual technical name) falling off. This completely flooded our downstairs. The plumber said it was due to cheap inserts being used. So my question is, should we have a plumber...
Is it possible to buy rubber radiator bracket, inserts for want of a better term, as in the photo to use with colum rads. Alternatively any suggestions as to a substitute item. I would prefer to use them so as not to have metal bracket touching metal of rad.
Hi guys , i got my oftec inspection next week .any advice ??
Has anyone else had inspection ?
Hes coming to inspect an install .
Someine has told me that i need to use oil pipe inserts every time .is this true ??
I have to reconnect some 22mm copper to a section of grey 22mm polypipe fitted with Hepworth grey screw connectors with rubber o ring and plastic grab rings. All of the fittings have worked for over 10 years and still seem good. Acorn Engineering still sell them but I'll have to order and I'd...
Hi all
Just managed to get a rothenberger rofrost turbo pipe freeze.
Went with the advise after considering bottled Co2 (thanks corbsy)
It was virtually for free - partly because it has no inserts
So im going to machine some and have some large round alloy bar here.
Can anyone measure the...
Hi could anyone confirm if pipe inserts are specific to the make of pipe or to the push fitting please as I have several makes of both inserts and fitting
Thanks
As the title suggests - I am converting my rads to centre exit 10mm speedfit pipe, feeding into Peglar pushfit 90's which are mounted to the TRV. The question is which insert to use? I am using the basic inserts with no rubbers for the compression fitting but have both types in my toolbox...
I...
Hi guys just been to see a job customer is complaining about two rads making banging noise after the heating has been on for about two hrs, could this be the trv's they are twenty years old
richardtheplumb
Thread
banging
cold radiator
hot rads
inserts
noise
quote
Today I was on a brand new plumbing & heating job. I have been asked to remove a rad & fit a smaller rad out further to allow a window seat. Also have to repipe a rad to towel rail swap & a basin to vanity unit swap.
TBH, it all is a bit of a DIY job (a builder did house refurb & most rads are...
Had a kitchen drinking tap which was connected after the water softener. Decided to connect it unfiltered straight to the mains supply. Noticed none of the 3/8 push fit pipe had inserts... It does seem pretty hard walled but is this correct? Thanks in advance.
Hi guys,
A customer has a kitchen mixer tap, quarter turn tap and need the innards replacing. I've bough both 1/2" and 3/4" and both don't fit. What's going on? It the same for another customer in have. Are these taps a direct size or are the glands I've bought cheap rubbish
help appreciated
beesley121
Thread
bought
cartridge
inserts
kitchen
kitchen mixer tap
mixer
mixer tap
number
size
tap
thread
Hi Guys and Galls :confused5::confused5:
I am installing a new central heating system with a external oil boiler. I intend to do all the pipe work and let the professionals fit the boiler. My plan is as follows:
22mm Copper pipe to and from the boiler in to the loft up through the chimney...
Now I have always and will always continue to use the hep2o pipe inserts on every single fittings, however a tiler who dabbles in the odd bit of plumbing now and again said he has NEVER used one when he has been using hep2o fittings but does use them for compression fittings. Now surely you need...
I am replacing my old shower mixer valve, etc, and propose to replace it with an Aquilisa 'exposed valve' using their easy fix bracket which has 'push fit' pipe/supply connectors. The shower hot & cold feeds are supplied via flexible grey (marked 'Hepworth UK Barrier pipe') 15mm polybutylene...
Haven't had much experience with plastic pipe apart from the occasional JG Speedfit fitting.
I'm off to get a few supplies and want to get a few 15mm pipe inserts. Do JG ones work in any plastic pipe or do I need to get a load of various ones?
It's not for any particular job I'm doing, just...
I'm a spark and i'm putting a new electric shower in my bathroom, pipes n all. I was just wondering if i can use plastic speedfit or do i need to use copper ?
th3pony
Thread
compression
copper
electric
electric shower
inserts
olive
shower
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.