Questions and plumbing advice in the Plumbers Arms - For Professional Plumbers only, with 50+ posts..
Some popular plumbing forums: Plumbing Advice - Plumbing Tools - Plumbing Courses & NVQ's
Forum Prefix Filter
Is Gledhill my only option for a direct thermal store?
They seem very expensive for what it is.
Got an all electric flat and the cylinder is in the centre so no where to take the prv for an unvented.
I have been asked to fit a Marco water boiler, it has a 3/4” bsp for the inlet but no hose with it(2nd hand).
Do I need a posh food grade hose £15, or can I use a washing machine one £2 for WRAS approved.
Anyone fitted these?
What do you think?
Easy to use or over complicated?
Are any of you guys fitting boilers and unvented with hot water priority?
What setup are you useing?
How do you size the boiler and cylinder?
I read the page from intergas in this months hvp magazine and would like to learn more
Anyone know a jetter in London I can refer good clients to?
Anyone fitted any of these ?? I've a rear flued ideal logic with water ingress issues I'm convinced it's driving rain ?.getting in the air intake it only happens in severely bad weather North eastly wind and rain .
I need to fit a wireless programmable stat to a Vokera boiler which I think can only do volt free switching. Does anyone have any recommendations of stats which can do this?
I’m fitting an Ideal Logic combi (in a loft) and nest stat next week.
If I wire it for open therm would it show boiler error messages at the stat?
Can anyone suggest a dehumidifier? I found and repaired a leak under a bedroom floor today. My customer is now dealing with the insurance company, carpet is soaking wet and smelly as leak has been going on a while. I have a wet Vac and lifted as much water from the carpet as possible, but a...
First job after my week's holiday, bit of a mess this one customer tried to tackle the strip out but needed a plumber, I've put it back together now ready for plasterer to skim the ceiling Monday and multipanel and fit out next week 👍 kop
I have been to an ariston e combi evo the I believe has a leaking main heat exchanger.
I can’t isolate the flow and return as they drip so need to open up the SS heat exchanger.
I have the new gasket but it’s not a full circle like Vaillant seals and is held together with a staple ( I assume for...
On googling it seems this is not sediment, just c02. It turns clear within a few seconds on standing still.
Also "more apparent in hard water areas and from models with perhaps slower and/or lower flow rates." Check and check.
What I want to know is why it only started recently?
It also started...
Hello all,
I've a job to check out some fill & flush valves on cisterns in the Braintree area and I'm too stacked out with work at the moment.
Is anyone from that area interested please?
Please PM me if your interested.
Cheers Jim
Evening All,
I have an unusual customer who is bit of a recyling nut. Last year we installed a heat only boiler (only after it died) and changed all his downstairs rads. It's only a small 3 bedroom house but for some reason he resisted getting a combi. Now he's having a loft extension there's...
Hi all. Looking at getting in to leak detection - ground mic, gas injection etc. Looks like the water board round us has increased its leak detection and is informing people of leaks on their side of meter - usually a cistern or prv etc. But there is obviously a call for more specialist leak...
Other than bes any suggestions on where I can get 5 water meter carriers with the blanking plate?
It’s a house split into 5 flats and they want the provision for meters to be added at a later date.
Greetings all
With the increased popularity of press fit and MLCP what are peoples go to brands??
I have used u-heat on here for UFH and MLCP pipe and fittings and they have been superb but I’m just curious if anyone would care to suggest preferred alternatives as well as m profile copper...
What do you think will happen in the future when we all have electric vans and need to charge them up at the customer’s property and electricity prices are sky high?
Will they read the meter and try and knock it off the bill?
Will we all have some sort of card reader where electricity gets...
Is it just my computer or is this forum now almost unreadable due to the quantity of huge and irrelevant adds? I kind of hope its my computer as I cant imagine the site owner wanting it to look like this, Ive never seen a website like it!
My core drill is all but dead (dewalt silver star)
Looking for a new one, any recommendations? Budget is around £300
Creating content since 2001. Untold Media.
Newest Plumbing Threads
-
king of pipes no reply from private message
- Started by cjg
- Replies: 1
-
-
-
Why pressure gauge drop without leak
- Started by sanju pradeep
- Replies: 3
-
Hot water so hot tap and shower via our hot water tank
- Started by thecar
- Replies: 4
-
-
Running copper pipework above / across a Gas boiler?
- Started by kristeva
- Replies: 2
-
Installing pipework to avoid airlocks
- Started by Matt0029
- Replies: 1
-
DUK Pipes for thermostat shower fitted at different heights
- Started by Delforkids
- Replies: 2
-
-
-
SPorcelanosa KRION Attica screen 1.2m, anyone?
- Started by Sebastian T
- Replies: 0
-
Cistern filling one third of the way
- Started by dwaindigital
- Replies: 4
-
Boiler losing pressure only on central heating- Started by SnosRap75
- Replies: 6
-
tanking. Is it ok to just seal everything with plastic.
- Started by Staggersandfalls
- Replies: 3