Discuss Air lock on hot water circs in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Andyh

Gas Engineer
Messages
34
hiya fellas and gals ...
Any one got a genius idea to remove air lock from 28 mm gravity circs...
I've bled the air valve on circs it's just water... was thinking connect hose pipe upto mains and backfill.. not what a customer advised and hit it with hammer :(
 
hiya fellas and gals .
Any one got a genius idea to remove air lock from 28 mm gravity circs...
I've bled the air valve on circs it's just water... was thinking connect hose pipe upto mains and backfill.. not what a customer advised and hit it with hammer :(

The right answer is to run the pipework properly so it naturally vents.
 
Of course you can. Tell the Landlord I said it. I was going to suggest the same as Shaun and Simon but it could go very wrong. It could also (if it's Primatic) cause days of orange water.

That's why I worded it differently :D
 
Temporarily remove a convenient radiator on the affected circuit. Connect a circulating pump (and, if you've got one handy a magnetic filter) across its connections. Run the temporary circulating pump until everything is working. Bleed radiators. Remove temporary pump, replace and bleed radiator.
 
upload_2018-11-28_22-38-47.png

OH NO!
IS THAT YOUR CUSTOMER?
 
Thanks fellas ,, I considered ripping up two bedroom floors to correctly realign the circs :eek: however tried to boil it out for about an hour then back filled it from mains .. not sure which way cured it but it seemed to be sorted thanks for those who offered useful comments :)
 
Thanks fellas ,, I considered ripping up two bedroom floors to correctly realign the circs :eek: however tried to boil it out for about an hour then back filled it from mains .. not sure which way cured it but it seemed to be sorted thanks for those who offered useful comments :)
Why the big red X disagree???
That's the first I have been given and I don't know why.
If it's a joke, kindly remove it.
 
:D
 
I have a BAXI SOLO 30 HEA.and gravity system cen. heating. The red ignition lockout light is coming on now and then together with flashing green lights for electric feed and main burner on.Have already replaced grundfoss
pump, flue seal, temp. sensor. Any idea whats wrong?
 
I have a BAXI SOLO 30 HEA.and gravity system cen. heating. The red ignition lockout light is coming on now and then together with flashing green lights for electric feed and main burner on.Have already replaced grundfoss
pump, flue seal, temp. sensor. Any idea whats wrong?

How can you have a Gravity system with that Boiler?
Are you Gas Safe Registered?
 

Reply to Air lock on hot water circs in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

I recently installed new hot and cold feeds to a new downstairs cloakroom. After refilling the system the hot taps were all dribbling, spluttering...
Replies
2
Views
608
Hi, I'm in my new build 2 years and the shower pump has died. I have an air to water unit downstairs is in the utility which I've been told is...
Replies
6
Views
295
Looking for any ideas to help. I've a Heatrae Sadia Hot Water tank, heated through Oil fired boiler (working fine). A week ago I reset the air...
Replies
8
Views
381
Hi Guys Need to pick your brains if you have a moment. I attended a flat where in one bathroom the hot water on the basin had major low...
Replies
3
Views
765
Hi, I have had this problem for a week now. The oil boiler will run for a short while and then stop. If I check the pipes around the 3 way valve...
Replies
3
Views
848
Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock