Honeywell Evohome with Worcester Bosch Greenstar System Boiler

[Mark8par]

I need a little help if possible as I am trying to check that my current system is running efficiently but not really sure how to check, sorry if this is a long one and I have tried to contact a Honeywell connected specialist but they dont seem interested unless installing a new system and the chap who installed ours has gone awol.

We currently have the following system
Worcester Green star 8000 Life System 35kw
Honeywell Evohome with hot water kit
All rads have HR92's installed
Megaflow cylinder
BDR91 x 2 - one controls CH and the other HW
2 x Motorised zone valve

I am seeing that the boiler seem to be firing quite alot and in short bursts, I have been checking my usage since we had a smart meter installed and considering we have alot of the rooms off most of the time the gas usage seems high and anywhere between 110kwh and 150kwh per day, to be honest the higher usage was when it was bloody cold though.

Anyway the system might be ok but I wanted to see if anyone has had any experience with this setup and has any advice.

thanks is advance and as I said I have tried to get professionals in but its just very difficult, hence I have resorted to a forum.

MH

 

[EvilDrPorkChop]

Would suggest checking the Minimum on time on the Evohome. The Worcesters seem to take a while to think about doing anything so by the time the Evohome has demanded and switched off the Worcester might only fire for 10/20secs.

 

[Mark8par]

Would suggest checking the Minimum on time on the Evohome. The Worcesters seem to take a while to think about doing anything so by the time the Evohome has demanded and switched off the Worcester might only fire for 10/20secs.

Thanks for the reply, would you be able to recommend a minimum on time?
Cheers

 

[EvilDrPorkChop]

Thanks for the reply, would you be able to recommend a minimum on time?
Cheers

With the Worcester i'd probably go 3 minutes, and 6 cycles per hour.

 

[EvilDrPorkChop]

Ideally, you'd of been better without the MV on the CH and you could then use the excess heat from the Pump overrun into the rads.

 

[Mark8par]

Ideally, you'd of been better without the MV on the CH and you could then use the excess heat from the Pump overrun into the rads.

Could I not then just leave the CH MV on permanent open?

 

[EvilDrPorkChop]

Could I not then just leave the CH MV on permanent open?

Not without any wiring mods, as it'll spring return on being powered.

Plus when they're manually open they're not open fully.

 

[Mark8par]

Could I not then just leave the CH MV on permanent open?

Cheers, I just wish I knew someone who can sort it out, the plumber I know does not install Evohome and never has. If I was to have the CH MV removed as far as I am aware the evohome will not do the boiler control with the Bosch so I can't use the evohome overrun unless you mean the Bosch will do it on its own.

 

[EvilDrPorkChop]

Cheers, I just wish I knew someone who can sort it out, the plumber I know does not install Evohome and never has. If I was to have the CH MV removed as far as I am aware the evohome will not do the boiler control with the Bosch so I can't use the evohome overrun unless you mean the Bosch will do it on its own.

In doing that you can then use the CH relay as a Boiler Relay instead. This will give you better control, and allow you to use the HW Overrun feature too.

Edit: The boiler will have it's own Pump overrun feature too. When a demand is switched off it'll overrun for so many minutes. You can use the excess heat for the radiators.

 

[Mark8par]

In doing that you can then use the CH relay as a Boiler Relay instead. This will give you better control, and allow you to use the HW Overrun feature too.

Edit: The boiler will have it's own Pump overrun feature too. When a demand is switched off it'll overrun for so many minutes. You can use the excess heat for the radiators.

Is it possible for the CH Relay (BDR91) to control the boiler, would it not require some re wiring? Also when you mention the over run can send excess to the radiators, if none of them are calling for heat would it not just circulate around the heating pipes or just sit in the (not sure what the term is) radiator in the hall that is open all the time.