Discuss Neighbours taps slam my pipes in the Plumbing Jobs | The Job-board area at PlumbersForums.net
Yes a complete hack out job so may just as well be 3.5" deep all the way :-0. luckily the timber pre 1950 was a lot better than the matchstick stuff i've been using upstairs.Combi boiler will not help. Now all your water pipes are on mains pressure running through the boiler, so any pressure surge from the mains supply will affect your hot pipes too, to some degree.
Your floor joists are FAR too substantial for you to be my neighbour: mine are only 6.25 x 1.5" ! Although I note the same 'notch out half the joist' technique has been used (joist notches should not be more than 1/8 the height of the joist).
So any of the other houses use water and mine are going to bang? :-( Surely this isn't normal?Combi boiler will not help. Now all your water pipes are on mains pressure running through the boiler, so any pressure surge from the mains supply will affect your hot pipes too, to some degree.
Thanks. Pipe will be moved above cables as there are even some cables over the top at some place. Very disappointed at sloppiness of install. Will need to cut pipe to do so as the cables will not be removed from CU. so I may as well move it to the joist to the right or left .It's not 'normal', but then shared supplies aren't the norm these days. I'm used to the noises mine makes and don't usually notice it, though it can sometimes be useful to know when the neighbour is in or out.
In the days of Garston, Croyden, or Portsmouth ballcocks, and taps to BS1010 the shutoff was gradual and so water hammer was less likely. As an experiment, you can probably open your stopcock fully and you'll be fine as long as long as you turn taps on and off slowly.
On a modern supply pipe feeding one dwelling, any water hammer (pressure transients) are removed by a substantial length of pipe from the next dwelling and connect back to a wider bore pipe in the street. As you presumably have a single 1/2" bore pipe supplying two dwellings, any water hammer hasn't got far to go before it can cause a nuisance and the narrow bore means the water is travelling at speed down the entire pipe length.
To be honest, that wiring is a snake's wedding: I have seen PVC cable cores push right through the insulation when in contact with a hot pipe, so I hope it is kept away from hot pipes! Also, 15mm pipe should be supported every 1.2m horizontally (about 4') so that isn't the greatest plumbing job either. It is also considered good practice to keep a 25mm clearance between electrical cable and any pipework. The proper way to support it in that location would be Munsen rings, or you can use plastic clips on a very long screw with a pipe offcut over the screw to give a decent length. Thinking alternatively, you might even be able to suspend it with some loops of cloth (old pair of jeans could be cut up) held by screws and washers to the joist on each side of the pipe. But sitting on cables is not an option.
If he does...?Do you have a water meter?
No i don't. Why, is that likely to causeba problem too?Do you have a water meter?
Thanks, was looking at this currently. Was about to use a few saddle clamps on the straight run first and see if that helps.I would try putting a small expansion tank on a tee right where the water line comes in. It will act as a big shock arrestor. When you secure your pipesuse something with a rubber insert. I don't know what you have available but I would suggest short pieces of insulation with a larger pipe clip around it. This way the foam insulation acts as a vibration dampener.
If you can get some polyethylene water line you could make a loop at the main, this may help with vibration as well.
I have lifted floor and see the hot pipes are, as you indicated, also affected.Combi boiler will not help. Now all your water pipes are on mains pressure running through the boiler, so any pressure surge from the mains supply will affect your hot pipes too, to some degree.
Hi scott_d , can you, or any other posters , recomend any particular makes of shock arrestor and pressure reducing valve from experience?Shutting the stop tap reduces flow not pressure
Cut out any dead legs that can trap air
Clip pipes
Pressure reducing valve
Shock arrestor
Reply to Neighbours taps slam my pipes in the Plumbing Jobs | The Job-board area at PlumbersForums.net
We get it, advertisements are annoying!
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.