Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

Recent content by Activate Trade Training

  1. A

    Help sourcing imperial fittings/adaptors

    Yes, 27mm OD is likely the old 3/4" imperial pipe. To connect it to modern metric pipes, use a 3/4" imperial to 25mm metric compression adapter. Ensure the fitting is WRAS approved for UK use. Verify the pipe material (PE) before fitting to ensure compatibility.
  2. A

    Cold water issues in the top bathroom

    The lower pressure in the top bathroom's cold tap and the whining noise from the toilet suggest air may be trapped in the pipes. The suggestion about cleaning the washer is a good first step. Have you checked for debris or airlocks in the pipes? You could try bleeding the system to release any...
  3. A

    UFH with Capillary Type Mixing Valve

    Yes - the recommendation above is accurate for your system. This system relies on a higher temperature difference to effectively mix and achieve the desired manifold temperature. Your current issue indicates the water isn't hot enough to meet the desired 45°C setting. The efficiency of the...
  4. A

    Electric shower problem

    It sounds like your shower might not be getting enough water due to the way it's connected. When teeing off a toilet's cold feed, you might not get enough flow for a good shower. First, check if there's any blockage in the pipes or shower head that's reducing flow. Also, ensure the pipe size to...
  5. A

    Shower problems

    Anthony - it sounds like there might be an issue with air trapped in the pipes or a partial blockage affecting your rain head's performance. Since the handheld shower works fine, the problem seems isolated to the rain head path. Try running both showers simultaneously to help remove any air...
  6. A

    Digitron APM140 Differential Manometer - Out of range issue

    It sounds like your meter might be in a locked mode or has a calibration issue perhaps? Try resetting it to factory settings - you can look for a reset button or option in the menu. If that doesn't work, check if there's a specific combination of buttons to unlock or recalibrate it.
  7. A

    Re: heated towel rail stopping working

    That valve replacement seems to have affected your towel rail working... First off, check if the valve settings were correctly adjusted for your towel rail. If pressing the flame button temporarily fixes it, then chances are there could be an airlock or the valve isn't opening properly. Try...
  8. A

    Radiator return valve shutoff issue

    It sounds like you've encountered lockshield valves, which are common on radiators but often don't have those more visible handles found on TRVs. These valves are designed for a specific setting and not regular adjustment, which is why they seem less accessible. To turn these off, you typically...
  9. A

    Sink drainage

    Yes, waste pipes can indeed go straight into the ground, especially in newer builds. When flooring around this pipe, ensure a neat finish by leaving a small gap around the pipe to accommodate any movement or expansion. You can use a flexible sealant or a grommet to seal this gap, preventing...
  10. A

    Some radiators not hot

    Check if the radiators are correctly sized for the room's heating needs. It sounds like it could be a circulation issue. Ensure the pump is working properly and consider flushing the system to remove any debris or sludge that may be blocking flow.
  11. A

    Four sewage smell coming from shower trap

    The presence of foul-smelling air and pressure from your shower trap isn't normal and indicates a problem. The water in the trap is designed to create a seal that prevents sewer gases from entering the room; however, a depth of 38mm might be insufficient for this purpose. The standard...
  12. A

    GlowWorm Boiler Burner Never Switches Off

    It sounds like your boiler is continuously running due to the absence of a room thermostat, leading to overheating. The flashing radiator icon and constant flame symbol indicate it's trying to heat beyond necessity. Installing a room thermostat will help regulate the temperature efficiently by...
  13. A

    gas service pipe under slab

    To be honest, burying gas service pipes, especially steel and copper, is not totally recommended without consulting local building codes and a professional first. It may require specific protection or rerouting to ensure safety and compliance.
  14. A

    Recent boiler room upgrade

    Great transformation - looks really good!
  15. A

    Can I use push fit type tap connectors on toilet fill valve

    Absolutely! A push-fit tap connector is suitable for providing flexibility and ensuring a secure connection without the need for soldering. Ensure compatibility with your pipe size and material for a leak-free installation. Good luck!
See more

We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.

Featured Content

Sponsors

Electric Underfloor Heating The Wetroom Store Heating 2 Go Electrical Goods - Electrical Tools - Brand Names Official UK Plumbers Forums Facebook Page PowDer Flush Gas Talk Group | Gas Safe Register
Back
Top