Search the forum,

Discuss Aldi holesaws coming in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
Also the garden sprayer for making one of these

by7ezety.jpg
 
Chemical pump for dosing systems. Also useful for other stuff
 
I got similar set of ordinary hole saws from Lidl at a sale for ÂŁ5.
Excellent for drilling holes in wood or plastic & most of the sizes are same as plumbers kit. They are decent quality & I assume those Aldi cutters are good for the money. Try buying a single top quality hole saw - they cost a lot more than that whole kit!
I slightly wiggle the drill around when drilling floorboards etc, as this gives the hole saw room to clear the timber & is easier on the drill & cutter.
 
Last edited:
I got similar set of ordinary hole saws from Lidl at a sale for ÂŁ5.
Excellent for drilling holes in wood or plastic & most of the sizes are same as plumbers kit. They are decent quality & I assume those Aldi cutters are good for the money. Try buying a single top quality hole saw - they cost a lot more than that whole kit!
I slightly wiggle the drill around when drilling floorboards etc, as this gives the hole saw room to clear the timber & is easier on the drill & cutter.


Definitely getting a set for a tenner, rude not to.
 
these are only ÂŁ12 are they any good does anyone know Makita Holesaw Kit 5 Piece Set | Holesaw Sets | NoLinkingToThis
 
check out the Chinese meal for 2 then!!! 3.99!!! ill be stocking my freezer up I think!!
 
I was quite surprised that my erbauer hole saw went through a cast iron soil pipe and remained sharp. I'd buy cheap ones again without hesitation
 
I brought the aldi ones last week, they look and feel quality. Very surprised!
 
Status
Not open for further replies.

Reply to Aldi holesaws coming in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hi, basic question, any insight much appreciated. Looking to have an outdoor tap in my front porch fed from 15mm pex coming up from suspended floor. Pic 1 is inside porch, pex temporarily clipped to give an idea of pipe placement (ignore shoddy blockwork of booted cowboy builder!), Pic 2 is...
Replies
6
Views
234
Hi all I'm hoping someone can shine a light on this for me Since our stop tap on the pavement has now been filled with sand for whatever reason, we are relying on our property fitted stopcock (this is outside on our garage wall) Unfortunately turning this to the closed position only reduces...
Replies
3
Views
250
Hi guys. I'm trying to identify a toilet model before ordering a seat for a customer. I went to what used to be a Roca stockist (they no longer are) and one of the guys there reckoned it might be "The Gap". I went to the new stockist and the guy there disagreed it was "The Gap" and that he'd...
Replies
2
Views
140
IS IT POSSIBLE TO ADJUST THIS MIXER UNIT? WE HAVE TO HAVE IT TURNED ALMOST FULLY ANTI CLOCKWISE TO GET HOT WATEROUT. THE FRONT PLATE WITH MIRA ON IT PRISES OFF AND INSIDE THERE ARE SOME PLASTIC BITS AND A SMALL CROSS-HEAD SCREW IN THE MIDDLE. THANKS
Replies
6
Views
227
  • Sticky
Morning to any Australians lurking around! Register its free, then message me, I'll sort your account out for you. We will need a moderator from each main country too. I'll post this in the Australian forum now.
Replies
0
Views
79
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock