Hints, tips & secrets of plumbing - No Banter please!

[WHPES]

re: Hints, tips & secrets of plumbing - No Banter please!

Leave it in a compartment in the top of your toolbox then it won't get lost under dust sheets etc.

 

[WHPES]

re: Hints, tips & secrets of plumbing - No Banter please!

Don't carry round junk and scrap and tools you don't need in your van, only adds to weight and uses extra fuel hauling it all around.

 

[Plumb-pro]

re: Hints, tips & secrets of plumbing - No Banter please!

When applying silicone along a bath, basin etc i always spray with windolene before smoothing, this stops any smearing up the tiles and bath and gives a great finish.

 

[iiplumbing]

re: Hints, tips & secrets of plumbing - No Banter please!

When applying silicone along a bath, basin etc i always spray with windolene before smoothing, this stops any smearing up the tiles and bath and gives a great finish.

I use the smallest amount of silicone possible and then from a cup of water wet my finger to smooth down. Different colour silicones sometimes behave differently, black being the most difficult (I used fairy liquid on finger to ease lubrication!)

 

[Dannypipe]

re: Hints, tips & secrets of plumbing - No Banter please!

13mm ratchet spanner on tail key. View attachment 11770

I like that. I resent paying Rothenburger 30 sheets for a posh spud key!

Here's a tip talking of boilers - purchase this set of magnetic trays from Toolstation :
Magnetic trays. That way you can put boiler components into them as you remove them, and not mix screws up.


I personally have a couple of these trays, also from Toolstation- but wished I'd bought the above set as it's better value.
Magnetic tray

 

[Whyme]

re: Hints, tips & secrets of plumbing - No Banter please!

Get a short piece of copper pipe with a stop end on to slide over your hot blowlamp nozzle when used in case it gets knocked over.

 

[CXR100]

re: Hints, tips & secrets of plumbing - No Banter please!

handy if you got the rothenberger blowlamp with the tip that goes red when soldering!!!!!! much prefer the bernzomatic!!

 

[CXR100]

re: Hints, tips & secrets of plumbing - No Banter please!

do everybody else's do this or just mine?? the bernzomatic tip stays coldish all times, but the rothenberger jest goes red hot straight away when i solder a joint!

 

[Dannypipe]

re: Hints, tips & secrets of plumbing - No Banter please!

Mine only gets red (glowing) hot if I turn the flame right down.

It always gets hot though! It's a blow torch.

I use Mapp gas BTW.

 

[CXR100]

re: Hints, tips & secrets of plumbing - No Banter please!

mine goes red whatever i try to do!!! i always use mapp gas with it, the bernzomatic tip doesent get red or hot tho!

 

[ne1ls0n]

re: Hints, tips & secrets of plumbing - No Banter please!

allways carry an extra roll of solder in the van, don't know how many times that one has bitten me

 

[Dannypipe]

re: Hints, tips & secrets of plumbing - No Banter please!

mine goes red whatever i try to do!!! i always use mapp gas with it, the bernzomatic tip doesent get red or hot tho!

Mine doesn't mate. If I'm sweating a joint and want to be careful with it, I'll wind the gas right down. Only then will the end start to glow red.

 

[mickg1]

when you fit a bath dont use the L shaped brackets there useless and you will get alot of movement from the bath, instead level the bath put a pencil line around the top of the bath ease the bath out of place and apply PINK GRIP adhesive about 10mm below your line, use plenty of it then throw your bath in place, give it a good wiggle to ensure it grips, if any goes on the bath dont rub it off, let it cure an it will just break off in go, (same goes for expanding foam if it gets on your hands dont rub it, let it cure an peal off in one go)

 

[Whyme]

Good skills or if youve a bit more time on your hands batten out the back and side walls so the lip sits on it.

 

[iiplumbing]

when you fit a bath dont use the L shaped brackets there useless and you will get alot of movement from the bath, instead level the bath put a pencil line around the top of the bath ease the bath out of place and apply PINK GRIP adhesive about 10mm below your line, use plenty of it then throw your bath in place, give it a good wiggle to ensure it grips, if any goes on the bath dont rub it off, let it cure an it will just break off in go, (same goes for expanding foam if it gets on your hands dont rub it, let it cure an peal off in one go)

I pity the poor fitter, who, in years to come, goes to remove one of your baths!

As for the "L" brackets, the problem with them is potentially splitting the wooden batten if you screw through without first pre-drilling. Also so many fitters (for ease of installation) put the bracket facing upwards (and then tiled over). Makes it a right pain if bath is to be removed without disturbing the tiles above!!

Why not put one bracket at each end (of the long side near each end) then one each on the near side, four brackets = bath reletively secure without the need for any adhesive, dont forget to use the lock bolts on the legs (they help stabilise as well and (before you tile) a sufficient but small amount of clear silicone between the bath edge and wall.

This silicone will be thin enough to secure but not enough so as to make it impossible to remove the bath without destroying the wall behind.

The finishing silicone then becomes a waterproofing and decorative layer and although it will also provide some mechanical grip that is not is what is intended, thus this top layer does not become stressed and fail causing a leak path.


www.iiplumbing-services-derby.co.uk