Search the forum,

Discuss Honeywell Evohome good or bad. in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
Messages
1
I'm thinking about installing a Honeywell evohome system in my own house. It looks good on paper but I'm still in two minds as it's a lot to spend. Has anyone out there got experience of fitting or operating it?
 
Yeh fantastic system but expensive, Massive control on every room if getting the full kit , well worth it ,
 
Agreed lot of kit for your £££
 
I had this installed in December 2017. I had some teething problems with the installation as it showed up some faults that were there, but undetected, in the original heating system.

The hot water zone valve was sticking and partially open (sometimes) and the hot water was not being correctly controlled. Now replaced.

Two of the original TRVs were not operating correctly and were casing vibrations in the pipework when partially open. This became much worse when a radiator was replaced and the TRV moved from flow to return. In investigating the cause I found a second original TRV that was also causing vibration. Both of these TRVs have now been replaced and we have no further vibrations.

I have had a problem as yet not resolved where a radiator control head loses connection to the Honeywell controller. It can take over two hours for it to reconnect. It has not done this for over two weeks. The RF checks show a signal strength of between 4 and 5 (max). Whether the vibration was causing this - who knows?

Apart from these issues it is proving very easy to set and change timers for each room. We have 12 zones. The radiator controllers make a whirring noise when adjusting but is is not too annoying.

I can't yet judge whether it will save any money as the winter has been much colder than last year and we have only been in the property for 18 months.

I had some difficulty finding an installer. The Honeywell web site had a feature to invite installers to contact me but I am still waiting. The first two heating engineers disappeared (no response to emails) between the first contact and 6 months later deciding to go ahead. I did eventually find a local company that had installed a small number of systems and so seem to understand it.

I did a lot of research into competitive systems and in particular about any security vulnerabilities (by profession I have been a network security specialist - now retired - responsible for the integrity of a number of critical systems). For example I would never accept a system that depended on having a mobile phone as the sole means of controlling it. There is too great a risk (in my opinion) of a compromise revealing whether the premises are unoccupied = heating switched off) and Honeywell's competitors did not seem to understand this issue. Honeywell also refused to answer my questions, or reveal their communications protocols, but their Evohome system will operate without Internet access which makes me feel a little more comfortable and I judge the risk to be just about acceptable. It is not regarded as good practice to rely on security by obfuscation. Security measures should be open to critical inspection by experts (far more capable then me) in order to be trusted.

I am however pleased with the end result so far.
 
Status
Not open for further replies.

Reply to Honeywell Evohome good or bad. in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
159
I have had a look at previous posts and think I know the answer to this but just before I make it worse could I just check what you think about this one. Granddaughter just moved house and this valve decided to leak when it was closed. When open its fine. Normally I have repacked the gland on...
Replies
7
Views
214
Can anyone recommend a decent multi meter, preferably under a 100 pounds. It's for checking boiler components so I don't need a top spec one ....just easy to use and reliable. The fluke 115 looks good but its above my budget. My current socket and see one was great but it's developed a fault.
Replies
7
Views
254
Copper pipes, I think its fair to say, is not what it used to be, the copper is getting thin while the cost is going up. Meanwhile, plastic Pushfit seems to be getting better and better, cost and convenience was always better, but now the quality is to, have we reached a stage where plastic will...
Replies
2
Views
276
Hi, Can anyone advise as to why the cold water to my bathroom keeps airlocking? This originally happened about 12 months ago and has happened 3-4 times since. It’s an upstairs bathroom, fed from a tank in the attic. The tank is about 8 Meters away and feeds a bath, sink and toilet. The tank...
Replies
9
Views
373
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock