Search the forum,

Discuss Will One Shot damage seals on push fit waste? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.

WaterTight

Esteemed
Plumber
Subscribed
Messages
5,439
Might anyone know...

Their FAQ doesn't A this Q.

Thanks
 
It could
 
Hi Water Tight,

Got absolutely no idea what you are talking about.

But with your luck of late, I would give it a go.

It could be something that turns the corner for you, or something that just keeps the ball rolling down hill.
You never know unless you try!!!

How did you get on with the basin?

Oz
 
Hi Water Tight,

Got absolutely no idea what you are talking about.

But with your luck of late, I would give it a go.

It could be something that turns the corner for you, or something that just keeps the ball rolling down hill.
You never know unless you try!!!

How did you get on with the basin?

Oz

Drain cleaner
 
Yep I would be a bit wary , but it is supplied in a plastic container so should be ok
 
Yeah if it wasn't for bad luck some times I think I'd have no luck at all.

Basin is ongoing but a solution is round the corner I hope, will update

Thanks Shaun and Jon. I imagine the chance is an outside one of a problem but I'll try the slower manual methods first.
 
I hate the stuff. Always worry about causing more damage than good.
 
I poured it do my kitchen sink once and it blew the trap off
 
Just pre warn the customer about this stuff prior to using it. I poured it down a shower waste once my phone rand answered it , by the time the call was over it melted the trap lol
 
Just pre warn the customer about this stuff prior to using it. I poured it down a shower waste once my phone rand answered it , by the time the call was over it melted the trap lol
Think that Dam Buster is better don't like one shot, But never had any problems , just ask if they have put anything else into drain first it can make a nasty gas if mixed with bleach
 
  • Agree
Reactions: rpm
Status
Not open for further replies.

Reply to Will One Shot damage seals on push fit waste? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Does anyone know where I can get one of these? Toilet is leaking into the bowl. This one pushes in with a half turn but I can't find one anywhere.
Replies
2
Views
213
Hi All, I am looking to take my bath out and fit a shower. Regards to tanking. Is it ok to just seal everything with plastic rather than just paint tanking slurry? Thanks in anticipation, best regards Staggers
Replies
3
Views
246
Hello I am looking to install a slimline dishwasher (integrated) into a cupboard in my kitchen. The depth of the dishwasher is 550mm and the depth of my cupboard is larger than this. The issue, however, is that the waste pipe which leads from the sink (next door cupboard) comes out quite a...
Replies
22
Views
466
The fittings below are for a mixer bar attached to a self contained shower. i.e not a wall. The attaching screws have snapped. I could get two new brackets, dismantle that existing one and start again or I could try and re attach via those screws, removing the broken ones from the plate and wall...
Replies
1
Views
226
I was stupid enough not to check the position of the pipes under the tiles when installing a toilet and drilled right through the center of a 16 mm copper water pipe. I exposed the pipe by removing a ~30cm section of the plastic sleeve and a ~10 cm section of the pipe around the hole. Several...
Replies
0
Views
213
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock