Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws
ShaunCorbs's latest activity
-
ShaunCorbs replied to the thread Best way to label pipes.But if your changing boilers heat onlys are more expensive than combis to buy -
ShaunCorbs replied to the thread UK Problem with Grundfos UPS 3 pump?.This is very strange Cavitation means no flow, can be caused by no flow / shut valves etc or dirt in the impella My recommendation would be to split the pump and see if there’s dirt in the impella
-
ShaunCorbs replied to the thread Best way to label pipes.On average feedback is around 1/6 saving going from heat only to combi / on demand
-
ShaunCorbs replied to the thread Best way to label pipes.That’s the thing though Heating pipes are at the location so no need to alter / add these Hot and cold just need to be run to the airing cupboard/ cylinder location in 15mm Gas need to be there but you can’t install that
-
ShaunCorbs replied to the thread Best way to label pipes.Would leave it to the pros as depending on Boiler locating might not need to be in that position
-
ShaunCorbs replied to the thread Leaking bottom fed toilet cistern ball valve entry.The washer either rubber or fibre needs replacing after you’ve disturbed it unless it’s brand new You should have enough flex in the vertical copper pipe to move it forward 2-3mm How tight is your plastic Cistern nut as this being...
-
ShaunCorbs reacted to Dan's post in the thread PlumbersForums.net has changed to PlumbersTalk.net with
Like.
It's back mate we still have bugs though. Working through them, the style first, that's not taken well. -
ShaunCorbs replied to the thread PlumbersForums.net has changed to PlumbersTalk.net.1 2
-
ShaunCorbs replied to the thread Shower hot then cold, but goes hot if basin tap is on.Think what last is trying to say if all the hot taps are working with no issue, then it could be the shower at fault
-
ShaunCorbs replied to the thread Leaking bottom fed toilet cistern ball valve entry.Did you replace the washer between the copper connection and the ball / float valve ? And any reason why you couldn’t get it central in the hole ?
-
ShaunCorbs replied to the thread Gas Rating App.Double the reading ? Eg if start is 00.352 and end is 00.402 60 seconds will be 00.050 120 seconds will be 00.100
-
ShaunCorbs replied to the thread Gas Rating App.Baxi app is free and has it I use the one below also
-
-
ShaunCorbs replied to the thread Flush Pipe Diameter Mystery.2” flush pipe You can make a rubber flush pipe seal work but it’s a stretch will get a link 1738187431 https://www.wickes.co.uk/Fluidmaster-Internal-Connector-Flush-Pipe/p/150176 1738187521 You can try these also Hanforede 2 PCS Flush...
-
ShaunCorbs replied to the thread Flush Pipe Diameter Mystery.Do you have a picture of the existing flush pipe and connector ?
-
ShaunCorbs replied to the thread Flush Pipe Diameter Mystery.Both ends the same size or one end bigger ?
-
ShaunCorbs replied to the thread UK Problem with Grundfos UPS 3 pump?.Yes try that
-
ShaunCorbs replied to the thread UK Problem with Grundfos UPS 3 pump?.Leds shouldn’t flash your still in pp You want solid colours eg fixed speed
-
ShaunCorbs replied to the thread UK Problem with Grundfos UPS 3 pump?.And it’s on cp 1/2 ?
-
ShaunCorbs replied to the thread UK Problem with Grundfos UPS 3 pump?.Right ok try opening valve 1 around 2-3 turns if it does
-
ShaunCorbs replied to the thread UK Problem with Grundfos UPS 3 pump?.Do you know if the heating was still on / calling ?
-
ShaunCorbs replied to the thread Single radiator in a large room question.As condensing boiler aim for dt of 20 So flow will be 60c return 40c 60+40/2-21 Mwat Dt29 To get conversion factor as most rad output are at dt50 29/50 xy1.3 = 0.492 Room requires 2931w 2931/0.492 So in dt 50 wattage you will...
-
ShaunCorbs replied to the thread UK Problem with Grundfos UPS 3 pump?.Half way from fully to closed
-
ShaunCorbs replied to the thread UK Problem with Grundfos UPS 3 pump?.Sounds like the pump is cavitating eg not pumping Valve 2 should be open 1/2 way
-
ShaunCorbs replied to the thread Fitting temperature stop concealed shower.Use a thermometer to set the temp before putting the dial on eg 38c set dial to 38c etc
-
ShaunCorbs replied to the thread Cohostore - Legit or not ?.Nope but looking at it, looks like a Chinese scam site they do everything bet you will be closed in 2 months and off with the money
-
ShaunCorbs replied to the thread Single radiator in a large room question.I thought it might be digital multi meter
-
ShaunCorbs replied to the thread Single radiator in a large room question.So 60 probably So conversion factor 0.492 So 1000w at dt29 will require 2033w at rad spec of dt50
-
ShaunCorbs replied to the thread Zoning systems.Open zone on ashp to get maximum efficiency As for zoning eg upstairs and down you don’t increase the Heatloss you just increase the demand eg downstairs will temper upstairs eg if downstairs is 20 upstairs will be around 18 if not heated
-
ShaunCorbs replied to the thread Single radiator in a large room question.What’s your flow temperature?
-
ShaunCorbs reacted to Dan's post in the thread Working on the forum this week (Jan 2025 onwards) with Like.
Okay, I'm now working through the forums and categories and simplifying them. And I'm trialing ads for those who have not visited for 24+ hours but not many at all for those who have. And then another one I'll bring in, as if a...
-
ShaunCorbs replied to the thread Single radiator in a large room question.Have a look at a k3 rad will need 15mm pipework if you have 10mm it’s a no go
-
ShaunCorbs replied to the thread Connecting Evohome to Worcester RI for modulation.I don’t believe the ems port is usable it’s there but not fully built in Also how does it know when the hot water is being heated it doesn’t, it’s a dumb (in wiring sense) all it’s looking for is 240v on the heat terminal Also that...
-
ShaunCorbs replied to the thread Connecting Evohome to Worcester RI for modulation.Also the easy control adapter is only compatible with combi boilers https://www.worcester-bosch.co.uk/professional/products/accessories/easycontrol-adapter Ignore the s plan part as that related to combi boilers s plan systems
-
ShaunCorbs replied to the thread Connecting Evohome to Worcester RI for modulation.But not usable for control / not sense compatible As you have a cylinder that needs to be kept at 65c So if you wc / opentherm it regulates the flow temp this is no good for the cylinder
-
ShaunCorbs replied to the thread Connecting Evohome to Worcester RI for modulation.Sorry to say you can’t as it’s a heat only you would need a system boiler
We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.
