Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

Install the app
How to install the app on iOS

Follow along with the video below to see how to install our site as a web app on your home screen.

Note: This feature may not be available in some browsers.

Search results

  1. A

    Baxi 105e issue

    Cheers Shaun, Was thinking it was going to end up heading down that route. Will save the customer in the long run so will see him tomorrow about replacing the boiler. Looking to drop a Baxi 830 in as very similar specs to the old unit, any thoughts from you guys on that. Also got another old...
  2. A

    Baxi 105e issue

    Fan doesn't spin up. Did on original reset but after that when fault re-occurred with the 30 & 50 lights usual clicks on boiler, pump runs & then diddly. M/Switches on diverter op ok, checked the looming for continuity, used flow diagram/chart & followed. Checked from overheat stat connector...
  3. A

    Baxi 105e issue

    Hi all, Just a quick one to tax your tired brain cells. Got a customer with one of these old beasts & i was called out to it late evening because of flashing 30 & 50 degree lights & no heating/hot water. Had a quick look at it and nothing obvious bar an occasional drip from the diverter valve...
  4. A

    Worcester cdi service...

    he's obviously earning too much then
  5. A

    GREENSTAR 25i GAS CONDENSING BOILER

    Drayton LP10RF Digital Programmer and Digistat+2RF RF560DR Try that one should give you time control & stat in one. I would use the W.B. Comfort 2rf but your shout
  6. A

    Pulsating combustion chamber flames

    Fan sealing poss, had that on an old W.B. 26 cdi extra for my sins. One of the old boys had a chuckle & told me about needing perfect sealing which is not easy to see sometimes, Cheers, Andy
  7. A

    Worcester cdi service...

    He will soon moan if you don't strip & then it goes **** up in the middle of the winter. Do it once & do it properly. He can then start saving for the next time it reqs a major strip/service out if boiler lasts that long. Best to change the bearing plate also because it usually takes the fan out...
  8. A

    Hot water and heating on at the same time

    Did the guy change the valve or just the motorised bit on top?
  9. A

    Help needed with this part

    Well you're builder installed it & as we all know builders know everything so just get him back & he can explain if you need it & the reason's why. As mentioned above by Snowhead the reason's they are fitted or not are correct supply dependant. Cheers, Andy
  10. A

    Glow worm betcom 4. Making noises

    Have you put a PRV &/or shock arrestor inline with oncoming mains as that may be a contributory cause to issue
  11. A

    Chimney Pots/gas terminals

    If in doubt refer to the regs or you could contact your center where you gained your gas quals from. They should be fully up to date with the regs and also maybe be able to explain them in a more simple way if you are struggling with them, Hope this helps, Andy
  12. A

    Worcester heat exchanger gasket?

    If you have located the seal plate tongue into the locating slot & then tightened it down in the front then you are all good. I always change the electrodes at the same time unless i know that they have not been in long. Simple design but sometimes can be a bit awkward with the new gasket &...
  13. A

    Gas meter display blank

    Sometimes you just have to make a call on things utilising your knowledge & past experience. If you are really worried then once the meter &/or battery was replaced by gas provider you called out you could go back to confirm gas rate with the FGA & pressure as mentioned above & annotate the CP12.
  14. A

    Help with putting dual flush valve back together :/

    Or replace cistern internals with a complete Fluidmaster refurb kit. All parts will be new for your peace of mind then.
  15. A

    Van 6-7k budget - work and motorbike

    Ducato or Relay/Boxer? Ducato good 2.3jtd/multijet engine & others PSA group 2.2hdi
  16. A

    2 tools that i would like

    For meter's i use Knipex pliers, don't mark anything & quickly adjusted. Also good for chrome items as don't mark them. https://www.ebay.co.uk/itm/Knipex-46672-400mm-Pliers-Wrench/192877557793? Pricey but you get what you pay for
  17. A

    Main combi 24 he hot water issue

    Might have to tweak the microswitch if you have fitted a refurbishment kit as some of the pins seem to be of slightly different lengths thus when demand is put in it does not fully make the switch, Cheers, Andy
  18. A

    Cheap cooker fitting jobs

    I don't know your pricing but as above if they want to pay peanuts then they can get some other monkey to do it for them or do it themselves. I've had it with servicing boiler & fires along with CP12 certification. I try to have a fair price for a good safe job & unless there is a very...
  19. A

    DIY Draining down system

    See if your hot water tank has an immersion heater. If so you can drain down central heating system, but make sure you isolate boiler electrically, eg - unplug or pop the fuse out of the switch boiler wire goes too. That way the water will be heated electrically without help of the boiler...
  20. A

    Wet vacuum advice? Mid budget up to £100

    If you are going to get the titan from Screwfix be aware the lid/motor unit is not held on tightly so when carrying it with a ltr or two of fluid if you bump it the motor unit & can will seperate & the fluid will spill out. When it has more fluid in it than that the weight holds it locked. As...

We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.

Featured Content

Sponsors

Electric Underfloor Heating The Wetroom Store Heating 2 Go Electrical Goods - Electrical Tools - Brand Names Official UK Plumbers Forums Facebook Page Gas Talk Group | Gas Safe Register Plumber Workwear Specialist

Featured Plumbing Threads

VividPromotion Workwear
Top Bottom
Back