Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

Install the app
How to install the app on iOS

Follow along with the video below to see how to install our site as a web app on your home screen.

Note: This feature may not be available in some browsers.

Search results

  1. Stants

    wetroom shower drain

    ah ok I see what your saying . been having a browse and ive found two sites that do what I wanted I was trying to get Osma products initially but they dont do all what I need but Polypipe do cheers for your help much appreciated
  2. Stants

    wetroom shower drain

    Yeah funny you should say that I've just found " Bes " and another site called " Plastic Supplies direct " both do what I need cheers for your help
  3. Stants

    wetroom shower drain

    oh ok so reading between the lines of what you are saying its a " No " to reducing it
  4. Stants

    wetroom shower drain

    Hi im installing a wetroom shower tray the trap that comes with it is 50 mm diameter I was going to run in 50 mm waste pipe / Elbows and Tees the under floor in solvent weld , and as it goes outside into the stack in push fit ( for ease of getting into if there is ever a blockage ) trouble is...
  5. Stants

    upgrading / addition of Nest to heating system

    Hi I'm have a new central heating system New boiler / pressurized Cylinder 210 new mdpe main 25 mm its being done soonish ( plumbers busy at the mo ) how much more effort is needed to add a nest system or similar and what is entailed ? do you need new rad valves sensors etc. and could it be...
  6. Stants

    Mains uprating is 32 mm that much better than 25 mm

    yeah will go with 25 mm thankyou for your reply much appreciated
  7. Stants

    Mains uprating is 32 mm that much better than 25 mm

    Yeah it looks like the 32 mm is not necessary so will go with the 25 mm ......Thanks very much for your reply ...all the best
  8. Stants

    Mains uprating is 32 mm that much better than 25 mm

    I did contact water board and they can uprate it to a 32 mm but It will cost and take more time ( on the lead replacement scheme they are obliged to do it in a certain timescale ) and I'm not guaranteed it will be allowed as you have to prove you really need it so with the other replies I've...
  9. Stants

    Mains uprating is 32 mm that much better than 25 mm

    Hi sorry if this is a silly question I'm having a new heating system installed ( un vented ) my new mains is due to be installed ( moled ) in 25 mm MDPE , the Water companies going to replace the communication pipe under the lead replacement scheme , however its been suggested to me to...
  10. Stants

    Limescale build up on Cylinder hard water area

    Hi I'm going to have a cylinder replaced because its failing there seems to be a lot of limescale build up i have heard of inhibitors liquid form but also heard you get electronic ones that emit a frequency ? are they hard to fit and do they work Cheers
  11. Stants

    Unvented Water pressure and flow question

    Thanks very much for your help
  12. Stants

    Unvented Water pressure and flow question

    I'm defiantly going to uprate the mains in the near future its just at the moment with everything that's going on workwise I could do without spending to get it done now just wanted to make sure it was safe if it was a bit on the low side thanks' for reply
  13. Stants

    Unvented Water pressure and flow question

    thanks for reply ..... any idea about the water pressure and Flow if its on the Limit without uprating ?
  14. Stants

    Unvented Water pressure and flow question

    Hi I'm having a new System ( Unvented 210 Evocyl cylinder and Worcester bosch boiler greenstar ) I've got one bathroom, bath ,sink and toilet and a shower and toilet , sink in another I think that's deemed as 1 and a 1/2 bathrooms ive done a flow and pressure test ( details on an earlier post...
  15. Stants

    Trouble draining Heating system

    Hi I did a little when I used the cold feed to dislodge the blockage just finished fitting the trimmer and as a temporary measure I'm going to reconnect the Header feed tank but before I do that was going to use the mains feed like I did before to flush the system I was going to flush it until...
  16. Stants

    Trouble draining Heating system

    Hi again I disconnected the Header feeder Tank ,Cleaned out about an inch of sludge at the bottom I managed to push a small metal rod I had down the cold feed didn't really feel any resistance Topped up the pipe again till water was flush with the top and still wasn't draining so took the...
  17. Stants

    Trouble draining Heating system

    Yes it’s the feed and expansion tank If is full of sludge what are the options on clearing it you can’t flush it with the mains ?
  18. Stants

    Trouble draining Heating system

    Hi I only wanted to drain the water out of the header tank as its in the way of a Trimmer I need to put in ( Loft conversion ) so if i scoop the water out of the tank it should be ok for legionella in regards to boiler it kept cutting out so I've stopped using it a while ago as its being...
  19. Stants

    Trouble draining Heating system

    Hi all I have an old Vented system header tank etc...... ( im very soon replacing the whole lot ) I need to move the header tank so tried to drain down the system and the Tanks not emptying put hose on downstairs Rad to drain, and water came out but I'm pretty sure all I've done is empty...
  20. Stants

    Unvented Cylinder size ? ( Evocyl )

    ah ok that makes sense I see what you are saying thanks

We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.

Featured Content

Sponsors

Electric Underfloor Heating The Wetroom Store Heating 2 Go Electrical Goods - Electrical Tools - Brand Names Official UK Plumbers Forums Facebook Page Gas Talk Group | Gas Safe Register Plumber Workwear Specialist

Featured Plumbing Threads

VividPromotion Workwear
Top Bottom
Back