Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

Search results

  1. B

    MT10RF replacement on greenstar junior24i combi mk3

    The clock timer on the Mt10rf transmitter does not work, but it can be used in day mode to get the heating on. Is Drayton LP10RF a suitable replacement? I guess the receiver from this would need to be used rather than the existing Worcester one?
  2. B

    D2 from 15l under sink heater.

    I have a 10m run to get to outside, can this be done in 32mm polypropylene pushfit pipe?
  3. B

    Which ceiling fed pumped shower are you using nowadays?

    I used to like the Aqualisa Visage but now too expensive and unnecessary ‘smart’ features seem obligatory.
  4. B

    Fitting a pocket door.

    Have an en-suite to create from scratch, customer would like a pocket door into the room. Can anyone recommend a kit they have used, studwork will be 38 x 89 cls with 12.5” plasterboard and skim coat (~120mm total). I will be doing all the work but have never fitted one before. There seems to...
  5. B

    Screen jumping around drive you mad?

    Jumps so much you end up clicking on the wrong thread , it’s so irritating I’m off for a break from it - two weeks and we’ll see...
  6. B

    Anyone used Ferroli 50l unvented, any good?

    I’m talking about the wall mounted water in/out at the bottom, small unvented cylinders. I have used Hyco 50l powerflow unvented, they come with all the controls for just under 400. Anyone have experience of Ferroli SEV 50 l unvented as they seem quite a lot cheaper, 240.
  7. B

    Anyone know which diaphragm is in a Roca inlet valve?

    Is it torbeck, fluid master, regular ball valve or its own special one? I’m talking about that one in the lauras which has an oval float in a shroud.
  8. B

    Supply hose for water boiler

    I have been asked to fit a Marco water boiler, it has a 3/4” bsp for the inlet but no hose with it(2nd hand). Do I need a posh food grade hose £15, or can I use a washing machine one £2 for WRAS approved.
  9. B

    Anyone fitted an enamel steel shower tray?

    I have a Bette Ultra 1800 x 800 enamelled steel shower tray to fit. Anything I can find says to use leg/frame kit, which I don’t have and anyway don’t want the height. Anyone done one? Can I just bed it on tile adhesive? Not sure if the steel will “stick” - but if it makes a fully supported...
  10. B

    Which concealed cistern do you use in Calypso units?

    Anyone know which cistern to use in a 500 calypso unit, needs to be serviceable from the front as fixed worktop above (ps I don’t like Dudley Niagara!)
  11. B

    Close coupled that saniaccess 3 will fit behind?

    As title really, need a “modern looking” wc that will fit cistern to wall as usual whilst using a saniaccess3. I think I can do it with Burlington, but customer does not want the ‘traditional’ look ; just to be awkward .... Any suggestions? (Tried and tested)
  12. B

    Bath/shower mixer hot to bath but goes cold when put to shower?

    Going to look at thermostatic Hansgrohe ecomax today, the customer says it’s fine on bath fill but goes cold when put onto shower. I thought both went through the thermostatic cartridge and am unsure how what see says could happen. It used to work fine, I can only think cartridge is on its last...
  13. B

    Does PRV have to be next to megaflo

    Have a customer with a leaking prv on the cold water set for a megaflo. He wants it removing, as he has had a prv fitted on the incoming main to the house - apparently by someone from megaflo ( not sure if he’s got that right). What I want to check is; can there just be a prv on incoming main...
  14. B

    Powerflush or re-pipe?

    Inherited heating system (in when we bought) has been poorly maintained, no inhibitor most radiators rusty, several places when a magnet sticks to a copper pipe. Also inordinate amount of creaking/popping as system heats/cools. Combi boiler on ground floor, most rads on drops from reasonably...
  15. B

    Dudley vantage flush valve problem

    Concealed cistern, this one has pan fan and is operated by IR button if that makes any difference. The usual problem of letting by into pan, we are in a hard water area and things do get scaled up. I have replaced the niagara dual pneumatic flush valve yet still on occasion the valve will stick...
  16. B

    Tempering valve as HW Cylinder too hot.

    HW Cylinder is gravity, heating pumped therefore HW gets to boiler temperature. System is such that controls would be difficult add so I hope to add a tempering valve at the HW cylinder take off. This needs to be 22-22-22, am I on the right track and can you recommend one. I guess these must be...
  17. B

    G3 unvented training.

    Having recently fitted three Monsoon 3 bar pumps, two universal, I found myself thinking I would like to be able to offer my customers the alternative of fitting an unvented cylinder. These pumps are superb but quite costly (note I don't say expensive as I think they are good value) and...

We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.

Featured Content

Back
Top