Hi,
Looking for any (constructive ;)) feedback on the schematic below. Trying to find a way to make use of multiple heat sources (OV Heat only boiler and Thermal Store with woodburner/solar thermal).
All the major elements (except for the UDH) are already installed.
Boiler has PDHW and...
Hi I’ve done a BTU room calculator, going by the calculations I need a radiator 6407 BTU, and 1877 watts. I’ve found a radiator just over these calculations at 6581 but in the description delta T65 is 6581. Delta T50 is 4695. Delta T30 is 2433. I have a recently fitted combi boiler. Would this...
Had to have an Auto Vent Valve changed today so system was drained down from the boiler, as this is higher than all the downstairs radiators I am assuming it was only the upstairs part of the system that drained?
Anyhow, valve was changed and system refilled, started up on Hot Water only all...
Long time no see….
A follow up to this rather old thread;
Thread 'Radiator not heating up as quickly as others?'
Radiator not heating up as quickly as others? | Plumbing Jobs | The Job-board | Plumbers Forums -...
Hi I had my heating on for a few days all of a sudden there was no heating in downstairs radiators, when I turn the heating on it kicks in then turns of after 5 minutes. I have also turned up. The upstairs is heating up and pump is hot, i have bleed downstairs radiator , boiler was serviced in...
I am attempting to find out which one is the last radiator by using a DMM connected to a themocouple. All the valves are completely open.
(The floor is solid concrete)
However they all seem to heat up simultaneously more or less.
The reason for doing this is that a wish to add a radiator or two...
Hi all,
I fitted my first rad the other day and unfortunately both tails are weeping. Whilst holding the tail in my left hand I wrapped ptfe between 15 and 20 turns clockwise. I screwed them in with my radiator spanner as far as they would go, not quite up to the last thread though.
Im going...
Could I pull these flex pipes up by cable tying them onto the back of the radiator (it’s a double rad) Just wondering if the heat against the cable ties would be ok. I’ve seen the cable clips you can get but not much room for them. Any help appreciated
I’ve got this radiator that I need to drain down & remove to clean out due to sludge. Can I drain it with that drain valve on the left because as you can see that it connects to the radiator but that pipe also runs along past the radiator on the right?
Hi guys, got supplied some corner valves but they have a rubber to go into the radiator inlet to create a seal.
Well I imagine that's the idea, fit hundreds of valves but always used Ptfe or Loctite. Never actually seen one like this.
Will the rubber do the job, or should I remove and fit as...
Hi. Currently have 3 small double radiators (500x600) in our open plan living room/kitchen diner. Would like to change them for single panel designer radiators. Do I just need to double the size (1000x600) to achieve the same heat output? Thanks in advance for your help.
Hi all!
So I've got a 6.5m x 3.8m front room, it's an extension incorporating half of the original living room. I've worked out the BTUs needed but my question is will one rad in this space be enough? Putting two in at half the BTUs each will be a awkward mission but I'm a little apprehensive...
Hi
was looking for some help,
I am looking to change out a radiator in my Hallway, my issue is the center of my pipes to the skirting is 35mm and I cant seem to find any radiator with his minimum clearance let alone any nice designer style ones, can anyone help me out please
I want to replace one radiator underneath the window (which is useless when it's cold and dark becuase it's behind the curtains) with one tall radiator at each side of the window.
I imagined plumbing them in parallel like this. (The dark squares in the middle are where the existing pipes go...
Hi there
My radiator came off the wall today with weak wall plugs.
There was one screw that was acrewed into the wall without a wall plug. When I’ve unscrewed said screw. I was mean with a really squirting.
I’ve taken a bit of the plasterboard away and I can see the hole that some idiot...