Hello,
Do I need to put a check valve on the cold feed of a bathroom basin mixer tap if it's on a Combo boiler and the tap is dual flow as opposed to a single flow where the water is mixed in the body which I understand should have a cv?
Cheers
Can anyone advise?
The problem is - we have a cold water and hot water tap (two separate ones) in a downstairs bathroom - these are basin taps with a 'bell' like housing. Sometimes, when turning the taps on the water flow is very restricted - ie a trickle - other times they work okay... BUT...
Dear Professionals, could you please advise. I have standard mixer tap in my bath (its about 15 years old, i recently bought the house). The water comes out from tap itself in massive amounts, bath can be filled in 3min, same if i unscrew shower hose - the water will shoot up very high, however...
Hello, I've tried searching using Bristan, Grohe, Vado etc & get no results at all - I don't understand that!
Anyway, is there an existing post, or would anyone be kind enough to proffer their opinion on tap quality. As I see it, there are two parameters - quality/thickness of chrome plating...
Hi there!
When I run hot or cold kitchen tap, clean transparent water slowly appears in washing machine - this water smells - have to scoop it out! Not sure if issue is installation - washing machine is sited not far from sink (live in flat and kitchen small). Here is a picture of the piping...
I'm about to install a P shaped shower bath into a small bathroom. However I've noticed that with the bath in place it's not possible to reach under the bath to the pre drilled tap holes. Because of the circular shape there's also no line of sight to these either making it very hard or...
I have a dripping hot water bath tap. I have removed the top but underneath is a plastic cap ( see picture) but the cap will not come off to get to the cartridge, and I don't want to force it in case it breaks.
Anybody any ideas on how to remove it, and if it breaks where you would be able to...
I'm having a nightmare trying to find matt black wall or deck mounted bath mixer taps with 3/4 fitting that work on 0.2 bar.
From tank to tap, I have around 2.4 metres, so a pressure of a little over 0.2 bar. The flow measured from the tap currently fitted is 11 litres per minute. Pretty much...
Hi,
As I need to purchase two new taps for our en suite, I've noticed that almost all taps now come with flexi tails as standard. I've read some horror stories about these bursting / leaking so would prefer rigid fixings like the existing ones they are replacing.
I'm looking to purchase this...
Hello All,
I wonder if you can help me?
I have intermittent hot water low flow from all taps in my 4 bedroom house upstairs and downstairs. I can sometimes recover the usual water pressure by turning the hot and cold water taps on and off which seems very strange to me. There is no problem...
Hi
Anyone know of a pull out kitchen tap that has decent pressure?
I have had low pressure from this tap for a number of years and it's not helped with the two 10mm tails that must reduce even further.
Hoping something is around that I can use 15mm full bore tails and isolating valves but all...
Can anyone help me with an ongoing issue I've had since I had an annual service on my combi boiler, which is a Potterton Performa 24. Literally after they left I started experiencing yellow water (pale) from all my taps - hot and cold, including the toilet.
This was intermittent and then...
I have quarter turn taps in my downstairs bathroom, the sink taps were getting a bit stiff so I replaced the insides with Flomasta 1/2" BSP quarter turn ceramic tap glands from Screwfix.
They work fine but are really noisy unless on full flow or trickle, anything in between sounds like Niagara...
Hi everyone,
I turned my cold water feed off in the airing cupboard which supplies only cold water to my bathroom but it also turned the water to my toilet off is that a correct set up? Because it didn't used to before the stop valve in airing cupboard only turned off the cold water supply to...
Hi
I have a 22mm hot and cold water supply to new bath. The pipes finish with compression valves. I need a 500 mm tap connector hose to connect with half inch thread on the new bath tap. All the connectors at the main plumb merchants are 22mm x 3/4 inch. No one seems able to answer question...
Hi everyone,
Gas combi Boiler
Mains fed in all taps and shower
How do I balance the water pressure in all faucets in my flat. Every tap/water faucet is mains fed but the cold water is really strong in every tap that if I open the tap fully it flies out like a fountain but the hot water is not...
Hi everyone,
I need to replace the kitchen tap, all my neighbours have two single taps in their kitchen and bathroom whereas I have a single lever tap in the bathroom and kitchen.
Due to living in a flat and having a shared water supply I was advised to get a dual flow tap for the kitchen so...
Hello,
I have a few mixer taps to install in bathrooms and kitchen. The kitchen tap also has a wondering spray arm capability. On researching something else, i stumbled across people saying that a check valve should be placed on the cold mains feed. How can I tell if the mixer taps/spray arm mix...
I'm a council tenant and my bathroom basin is broken and needs replacing, it has standard pillar taps. Do you know if councils would ever replace it with a mixer tap one if I paid the difference? (I'm guessing no but it's worth a try).
How much more complicated and time consuming is it to...
Morning all,
I recently changed the washers on my kitchen mixer tap due to it dripping, I reseated it using a tool but it's still dripping. I have had another go today and on closer inspection of the seat it appears to have a hairline crack. Can this be repaired or do I change them completely...