Hi guys first post.
I am in the process of rejuvenating a double wash sink.
It was needing the waste below looked at for a washing machine and dryer, as it had a sunken elbow and unbeknownst it was a mix of 1 1/4 and 1 1/2, including the sink wastes themselves.
I bought new matching 1 1/2...
Does anyone know where I can get a DCV with an isolator that is WRAS approved?
I need one for an outside tap and have limited space so I could do with a combined item
thank you :)
I have an Elson Sapphire double feed indirect hot water tank and I need to drain down the system to move some radiators.
Would anyone be able to offer any advice as to the correct drain down and refill procedure for this tank?
It is a self contained boxed and insulated unit with a single cold...
Hi,
I have a fairly modern multifuel stove with a back boiler connected to a Elson Sapphire double feed indirect hot water tank and I need to drain down the system to move a radiator.
Would anyone be able to offer any advice as to the correct drain down and refill procedure for this tank as...
Hi all, I’ve a customer with a failed double check valve on a water softener, it’s 22mm compression but with a far larger bore than the usual DCV’s you see online. Anyone know if they are called something different or where I can get one? I’ve even been on the water softener website and they...
Hi, I have recently had a water board inspection
This is what the report said about the filling loop on our press unit for a biomass boiler….
There is quickfill pipework directly between the mains water supply and heating supply. This type of temporary connection is permitted under the water...
I have two sinks in our vanity and the outlet is in the centre. The wastes I have seen in Bunnings put the P trap under one of the sinks and the second sink drains to that P trap.
Unfortunately I am having draws under the sinks and an access door in the centre for the P trap but I cant find a...
Can anyone tell me what the nut is for on the side of the double check valve in the pipe leading to my outside tap? The valve is jammed closed and I wondered if it is possible to free it?
Steve Minnis
Thread
america
check
check valve
double
failure
usa
valve
Hey, just looking for a little feedback on the mock up I drew. I’m adding a washing machine and a double vanity to a 2” pipe I’ll have mounted into my main drain stack. For the vent off of the vanity, is it necessary? I’ve seen an “all hub 90” that would give me pipe to both vanities, but...
Marc m
Thread
america
double
machine
usa
vanity
vent
washing
washing machine
Morning!
Can a Reina Neva Vertical Double Designer Radiator 1800x472mm which is labelled front and back be turned around and still function optimally?
I have one which is dented on the front so would like to turn it front to the wall. I have been given conflicting advice whether this is...
When replacing 500x900 ( single) radiator with exactly the same size but double the boiler pressure drops. Is this because the radiator requires more water than the original?
Old radiator wouldn't get hot, so I replaced it with a new one and new valve's, And now it get quite warm at the back of it(double panel) but the front one is barely warm. I tried bleeding it, but no air comes out, tried balancing the radiators, but that does nothing, rest of the radiators are...
My double flush toilet has developed a fault. It won't stop filling eve when I pull the float arm right up. I have replaced the inlet valve diaphragm but this has made no difference
What else can i try?
I plunged each side of sink up top... disconnected trap below and ran water from each side. Water ran out fine so problem not here.
I ran a 3 to 4 ft snake down pipe going into wall under vent and no blockage. My problem is when i start to run sink water backs up and out the Proflo vent seen in...
Hi All
Attempted to fit a double waste outlet today (w/machine and dishwasher) but failed.
I purchase this from screwfix presuming i could i just swap/convert the current single hose outlet to a double but when i tried i realised it was for 40mm pipe/compression fitting and i could not just...
Does anyone know if the 15mm Talon double pipe cover with inside corner will accommodate 90 degree copper pipe bends?
In other words will the corner cover the curve of the 90 degree bend or do I need to use joints here?
Thank you
Long shot I know. Anyone got the above with vertical earth pipe at the back. Tried all the usual outlets. Understand only Twyfords and Armitage Shanks did them so anyone got an AS would need the Cistern as well.
Cheers
We have an old house where downstairs is an old single pipe system but upstairs is a conventional double pipe system when it was added later on.
The single pipes are burried in concrete so it's not an option to convert at this time
In an effort to improve downstairs we were looking at changing...
Need some recommendations for a large new build. (400m2)
3 showers, 5 handbasins, 2 baths, 5 WC's, 4 sinks, 2 dishwashers, 2 washing machines.
32mm incoming main at just over 3 bar.
mains gas.
The spec is:
Limitless hot water
full pressure for 3 simultaneous showers (15 lpm each) with zero...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.