Search the forum,

Discuss Surely a DIY install right? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Status
Not open for further replies.
That's why people get put off because most of the people haven't got a clue and installing things like this ... it makes much harder for us to get a job. People just going too cheap sometimes ... they don't want to pay a decent plumber to do a decent job, but paying twice ? ! :)
 
If it was a plumber who fitted that they are pretty green!! As I get older and more cynical I'm coming to the conclusion that the majority of the public simply don't want to pay enough to get a job done properly!
 
Croft; are you actually gasbusters on Diynot?

Don't blame the punter FFS: he has no idea what a job should cost, or how it should be done, and , anyway, the real cowboys charge over the odds and do work like this.

I cant be arsed to look beyond the first photos or properly read all the inane comments. (Apologies to those who provided sensible contributions ). I am not a qualified plumber,but a Gas Service Engineer, but I know the hot should not be run off the horizontal vent/hot supply. Obviously best to use a flange, but otherwise break into the vertical hot supply, before any other draw offs. The cold feed is not clear,but should be taken from the CWS, below the cylinder supply connection,

The job is a mess,but don't blame the punter who presumably pais ÂŁÂŁÂŁÂŁ's for the crock.
 
Heyup :) To be clear, I'm not blaming the punter. I just have my suspicions that he's done it himself to be honest, certainly didn't suggest that on the public forum though. This part of the forum is for us to discuss these sort of things privately :) On the public post I was very friendly with him!!

I'm not gasbusters though - I run Dripbusters in Lincoln. Didn't realise there was a gasbusters although I've seen a Stumpbusters in Lincoln. Even though I have never met the guy we wave at each other each time we drive past one another out of mutual respect for our company names :)
 
Status
Not open for further replies.

Reply to Surely a DIY install right? in the Plumbing Jobs | The Job-board area at PlumbersForums.net

Similar plumbing topics

Hi, My current hot water system needs to be replaced. Anyone got any suggestions or can recommend any plumbers around Derrimut area that won't rip me off? An office guy recommended me to apply for government rebates and get it installed through timetosave.com.au. How reliable is this...
Replies
6
Views
313
Hello plumbers in my internet. So the Mrs want a spray mixer tap in the kitchen as we had two separate taps. I changed the tap for a temporary two hole mixer but the cold water pressure is high mains fed and the hot is low pressure immersion tank fed. I've been trying to find info on what I...
Replies
2
Views
154
Hi bit of a weird issue, I installed a grohe bathroom tap successfully 2 months ago bought from screwfix. Last week the right hand hot tap makes a squeak noise as I turn it on or off, left tap is 100% perfect and noiseless. This grohe tap is like one unit, so no screw notch or way I can remove...
Replies
7
Views
249
I was stupid enough not to check the position of the pipes under the tiles when installing a toilet and drilled right through the center of a 16 mm copper water pipe. I exposed the pipe by removing a ~30cm section of the plastic sleeve and a ~10 cm section of the pipe around the hole. Several...
Replies
0
Views
208
The left rear floor corner is highest (the shower pan touches/sits on the floor), sloping down diagonally to the front right corner (lowest). The front right corner shim is 5/8", the left front corner is 3/8" shimmed, with shorter shims under left middle and right rear corner. The pan perimeters...
Replies
6
Views
207
Creating content since 2001. Untold Media.

Newest Plumbing Threads

Back
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.

I've Disabled AdBlock