back boiler fittings

[spycatcher]

Hi All, ive just aquired a coalbrookdale severn with a back boiler

there are 4 outlets at the back of it, three of them take 28mm pipe and one takes a 22mm pipe

one of the 28mm outlets i can fit an ordinary 28mm compression nut with a 28mm olive but the other two 28mm outlets and the 22mm outletseem to have a much finer thread on them

can anyone tell me what kind of a compression nut to buy for the other outlets

thanks

 

[SimonG]

Ones that fit.

Strip out and refit new MI x Cu conns.

 

[snowhead]

Second hand, with used fittings already in the back?
As above you will need to buy at least 3 new ones.
The compression nut thread on 22mm and above is usually unique to a fitting manufacturer, not BSP.

 

[spycatcher]

thanks for the reply snowhead

if i take these fittings out what ones would you suggest i replace them with

 

[Gray0689]

2xinch by 28mm
2x inch by 22mm

 

[spycatcher]

it says in the manual that it has 4 * 1 1/4 connections on the back

 

[snowhead]

It will have 1.1/4" to 1" iron bushes in the outlets and possible 1 x 1.1/4" to 3/4" iron bush.
Unscrew the brass fittings and leave the iron bushes in.

 

[Gray0689]

It will have 1.1/4" to 1" iron bushes in the outlets and possible 1 x 1.1/4" to 3/4" iron bush.
Unscrew the brass fittings and leave the iron bushes in.

Never saw a back boiler with 11/4 fittings

 

[snowhead]

If it's this one they're 1"


http://www.rayburn-web.co.uk/Prodin...iler/CBD Severn Blr inst 10_00 EINS 33713.pdf

 

[Best]

Your question shows you have little experience of plumbing - no offence intended, so I would advise you get someone with experience of solid fuel to help you or do everything. I just saw on Saturday a fire connected by someone who was a plumber of sorts but out of their depth. It is highly dangerous, with no primaries or independent vents/feeds.

 

[tamz]

Boom boom :smile:

 

[spycatcher]

Hi, this is the stove

Coalbrookdale Severn Multi Fuel Stove Spare Parts

my apologies, i have just read the installation manual again and it is 4 * 1 inch bsp female outlets

 

[rachaelcollins0]

Never saw a back boiler with 11/4 fittings

Mee too!!!

 

[spycatcher]

The brass fittings are proving to be a bit of a problem getting out

worried i round them

 

[Barry98]

The brass fittings are proving to be a bit of a problem getting out

worried i round them

instead of been selective of which replies you read and accept try reading them all please , would hate to here about you on the news

 

[spycatcher]

i have read all the replies thank you

 

[spycatcher]

Well thats great thank you all very much

its all very well for you to say to me to read all the replies and get expert advice etc. and if i lived in a city i would probably only have to clink two copper pipes together outside my front door and half a dozen plumbers would come running but i live in the highlands in the back of beyond where its easier to catch haggis than plumbers but thats ok i'll manage

thank you all for your advice and non-advice

 

[SimonG]

What you have failed to understand is the inherent danger of a solid fuel system and said system being installed by an obvious novice.
Your retort is exactly of others on here who don't like the answers to their questions. The reason why you have had no 'real' help with this matter is the fact that you don't have the first clue as to what you are doing and are therefore a danger to yourself and your family.

Here's some really good advice. Stop being tight and find somebody who knows what they are doing, before we hear about it in the news.

 

[spycatcher]

perhaps you should go back and read my post thourghly

the bit about i live in the back of beyond where there are NO plumbers willing to come and do the job

its hardly rocket science, i guess i'll just get my lathe out and make the nuts myself

 

[SimonG]

I always find that when there are NO plumbers that will do the job it's down to the customer. IMHO.

 

[spycatcher]

well thats just goes to show the level of your knowledge

 

[chris watkins]

perhaps you should go back and read my post thourghly

the bit about i live in the back of beyond where there are NO plumbers willing to come and do the job

its hardly rocket science, i guess i'll just get my lathe out and make the nuts myself

What a strange person you are spycatcher, it must be living out the back of beyond, if it is not rocket science then why are you asking on here ?

 

[Best]

Surely there is a solid fuel experienced engineer within 50 miles of you?
As to the seized fittings - use a blow lamp to heat outside the fittings (& a little heat on fitting) & if a spanner will slip, use grips to remove each fitting. Wear gloves to protect your hands. How's that for useful advice? :smile:

 

[spycatcher]

all i am asking is what nut could it be that are on the 3 other brass fittings

if you dont know then thats fine

go and harass someone else

 

[spycatcher]

thank you best

that sounds like sound advice

i live in the scottish highlands miles from anywhere

believe me tradesmen are as scarce as hens teeth up here