I've fitted a few of these now and had a few call backs with leaks. Anyone else had problems with these and which magnetic filter is the most reliable.......
Can anyone tell me if you can run all 5 pipes behind for upward piping on this model?
From the MI's it doesnt show the gas, just F&R H&C
Also does it have the key type filling link?
:santa3:
Hi,
I have the above boiler which is around 4 years old. Recently it has started giving me a number of problems and unsure if they are all related.
I now have these problems:
1. Despite the heating regulating dial being on very low the water is scalding out of the tap. However on...
Hi all,
called to look at a Vokera compact Se (2005)where there was water constantly filling from the domestic hot water over pressurising the boiler. Checked expansion vessel and ok. I can't see any divertor valve, so am I right in thinking that there is a leak in the heat exchanger between the...
Hi
all attended boiler flashing red/green call vokera stated faulty thermistor , replaced turned on no led at all. turned power of checked internal fuse ok turned power back on nothing off again left 30 sec tuned on fired up green light. landlord called tenant said gone off no led light so...
I have re-ordered a NK one compact soft close seat as the old one had broken (for NK compact WC set - free standing), the new seat is a slightly updated model with different hinges and fixing pins.
I need to get the old fixing pins out of the toilet itself but when I unscrew them there is...
Alreet ladies. After one tissue to the neXt. Went to compact 35he
Ratio 0.0082
CO 408
Co2 5
Burner 10.2
Inlet 10.2
Was diagnosed by service guy. I just fitted Venturi and then carried out checks, she were rough!
Clean side fine. So all I can think is that the gas valve been fully opened...
I have a problem with Vokera Compact 25he combi boiler. I'm registered gas engineer. When I came there first time I noticed that the boiler can't start because of air pressure switch. I checked that and it is ok. Replaced fan, cleaned vonturi then, so the boiler started ok on hot water and...
I'm fairly puzzled by this one chaps, it's the compact with the secondary heat exchanger that the fan blows through. It seems that condensate is running down passed the fan in in to the bottom of the burner chamber.. initial brief investigation seems to be pretty clear combustion air path and...
I'm having problems with this boiler. The diverter valve won't move at all. I have fitted a new div valve today, no change....
I have also changed the flow switch (on top of water valve). I have checked as best I can the capillary tubes and the pump seems strong.
I just can't get the flipping...
alright guys am not for one fitting viessman, I have had this in my unit for 8-10 months brand spanking new boiler (5 YEARS) the box is not the best but still holds the boiler fine, Nothing missing full boiler I am looking to get rid of it cheap as it sat in the garage doing nothing and I just...
Heres a funny one for ya'll, went to a compact 28 which will not ignite. Its had a new pcb and 2 gas valves as its getting to ignition stage and wont open the gas valve.
I checked for 240v at the board and 240v at the plug going in to the gas valve. I'm left thinking its a bad batch of gas...
Heating works fine, hot water works fine. When the heatings been on a while and the tennant runs a tap the boiler locks out.
Circulation issues of some sort is my thoughts? Anyone???
hi all,
I'm really hoping someone here can help. I've just installed a red compact 24 pellet boiler and switched it on for the first time and i get the following alarm code preventing the boiler from even firing for the first time 'A18 water temperature overheating', which obviously makes no...
I'm looking to get my boiler changed in the coming week and everyone seems to have there own opinion with what is a good brand/model and what is a bad one.
On balance I'm getting a good vibe about Intergas, but I'm a bot concerned that the output of the Compact HRE SB 30 boiler is rather low...
I have an Intergas Combi Compact HRE 36/30 (fitted 5 years ago) and despite different Engineers being advised by Intergas UKs technical team I still keep getting f11 faults resulting in no hot water (I have to press reset each time to get hot water again).
23rd January:
Flow switch...
Need to change a plate heat ex on one of these but the screws holding it in place have gone soft and it's just rounding off. Any ideas? It's too tight to get the grips on it and plastic manifold so I've got to be gentle
Looking at the 28 CDi Compact and the 28 Junior, the flow rates, heat outputs and dimensions of the Junior and Compact look almost identical to me so what am I missing? I know the Junor is the bottom of the range, but where is the extra money for the Compact going? I know the Junior didnt used...