Hi, Our gravity HW tank split and without a long delay the only one we could get was a fully pumped tank. Fairly easy replumb to get the tank in, however on all diagrams I've looked at, the fully pumped system has the open vent coming off between the boiler and the pump, whereas in our current...
Hi folks, I’m in need of some sound advice.
We have recently had a ground floor extension and have had underfloor heating (company: JK UFH) installed throughout most of the downstairs. We have a few rads still left downstairs and the entire upstairs is still heated through rads.
We have a...
Hi all
I’m curious about the conversion of my heating system
I have a gravity system with no diverter valves, the cylinder is quite small and there is an air separator present I am curious as to how this system would be converted to a combi system, am I right to assume that the flow and return...
question about connecting an ejector pump to the sewer, where there is no existing conditioned structure that gravity-feeds:
We have a lot that will be built in a couple years. Lot is sloped, with road and sewer main nearest to the up-hill lot line. The house will built in that corner, and...
All,
Need some ideas pleaeses and thanks.
Customer had drained system and had awful air locks, went round boiled out and got working... GREAT!
2 weeks later after some bumping and banging, no hot water. Went round and flow red hot, nothing on the return.
Boiled again... Got hot water...
I want to put in an electric shower in my downstairs cloakroom which currently has a gravity fed cold supply from the tank in the loft. The shower I am looking to install needs a mains fed cold supply which I could do by disconnecting this pipework from the gravity tank and connecting the cold...
Hi all. My customer has a bath shower mixer that gets cold from the mains and hot from a vented cylinder and the cold knocks out the hot. I'm thinking about putting in a thermostatic bath shower mixer but would appreciate any other ideas! Cheers all/
HI,
Looking for some guidance on buying and fitting the right products.
I currently have a gravity fed system with a cold water tank in the loft and a hot water cylinder in the airing cupboard on the first floor. The hot water flow throughout the house is not particularly brilliant, but sort...
Hello All,
I believe that some time ago I may have replaced the Shower Pump that stopped working after approximately 3 to 5 years or more with the wrong Shower Head Pump type.
The Shower is Gravity Fed from the Cold Water Tank in the Loft above the Bathroom where the Hot Water Tank is within...
Good morning all,
-I would really appreciate your advice on whether it would be possible to have a gravity fed toilet, basin and shower installed in a my new layout upstairs?
The detail:
I currently own a two bed house (is actually a three bed on original plans) and want to covert it back to...
Forgive me is this is a stupid thought!
I'm looking to flush dirty water out of an F&E system. Can I attached a hosepipe to the lowest drain off point and simply drain off water outside without turning off the water supply to the F&E tank? So my thinking is that it may take some time but...
We've had conflicting advice from two plumbers - I wonder if anyone here can clarify.
We have a gravity fed system system, currently with the hot water cylinder alongside the boiler which is in a separate 1 story room with some roof space. We're looking at moving the cylinder into the roof...
HI everyone,
I went to look at a prehistoric gravity fed Ideal Vulcan SX / DLX boiler with reports of no heating or hot water. This is a 4 pipe 28mm pump fed heating and gravity fed water pipes to water cylinder. I found that the heating pump had stopped spinning and found sludge behind the...
If a conventional system is changed to a combi boiler and the twin boost pump and CWST have been left in and working would it be an issue that gas safe can get involved with ?
The mains hot water and tank fed cold water was running through pump and because pump stopped working cold water...
Hey to all in the community, im not a plumber so any advice would be greatly appreciated.
I reside in rural ireland and we currently get our mains water fed to us from a pipe which is one 1km long from a stream out the back of our property. It is then filtered with rocksalt, uv, Reverse...
About 10 years ago we had a new mixer shower fitted. However, the most we ever got out of it was a trickle - even from the beginning. At the time I looked up the manufacturers installation instructions and it says that the showerhead needs to be at least 1 m from the bottom of the water tank we...
Hello,
I live in a building that is a conversion of two terrace houses into several flats. We have 7 levels (basement, ground, 1st, 2nd, 3rd, 4rth, and 5th), and each level has two flats, except for the 5th floor, which is the attic and on one side there is a small studio and on the other side...
I am a retired Chartered Electrical Engineer and am looking for information about the necessary conditions for gravity primary circulation in a 28mm domestic indirect vented hot water circuit.
Until recently I have fitted Hercal cylinders in my house and they always worked without any...
Hi have been asked to fit an unvented cylinder (I’m G3) but the heating system is as follows.
ideal Mexico 2 boiler
gravity hot water pumped heating
28mm flow and return from boiler to cylinder with 22mm flow and return to boiler with pump for heating.
is it possible to put an unvented...
Hi,
I’ve been to quote for an en-suite for a customer and they like the idea of these digital showers .
I’ve not fitted many of these digital showers and when I have it’s only been on unvented systems.
Was wondering is the pressure and flow good on the digital showers ? I know you can get...