Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

immersion

  1. Husk24

    Immersion heater/constant or timed?

    Hi All I have a 200 litre water cylinder which I heats up the water using my gas boiler. This was already in my house when I moved in it 3 years ago. Until recently I have had the timer on from 6am- 9pm every day with temp of around 60 degrees. As I have had my new boiler installed and nest...
  2. batwad

    Why disconnect an immersion heater?

    I moved house a few months ago and am slowly but surely figuring out its nuances. Wouldn't it be wonderful if houses came with wiring/plumbing diagrams that showed how everything connected? Anyway... I've got what I understand to be a pretty standard gravity-fed vented heating system, with...
  3. T

    Unvented santon (45 yr old?) immersion heater with gravity fed tank?

    Hello, I hope someone can help, we recently were forced to move to a ground floor social housing flat because of my partners worsening health condition. It has an assisted shower with a mira advanced thermostatic low-pressure shower unit so hot water for baths isn't a problem. However, the...
  4. T

    Hot water cylinder with immersion tripping rcd.

    Hi guys. I have a newish (4 years old) hot water cylinder with 2 immersion heaters fitted. It has worked fine but yesterday when switching it on it tripped a rcd. I have disconnected the mains from the element put it in terminal strip and tried the switch again and it doesn't trip so I would...
    • Toddius
    • Thread
    • cylinder hot water immersion water water cylinder
    • Replies: 14
    • Forum: Bathroom Advice
  5. T

    The final return tee: always the immersion cylinder return, but is it a standard?

    Hi, Long story short: my boiler (gas, conventional, vented, three port system) has been moved from one side of the house to the other. Previously the immersion cylinder return was the final tee before reaching the boiler, and all worked fine. Now the immersion cylinder return is a few tees...
  6. E

    Worcester oil boiler and water immersion heater question

    I have a Worcester Greenstar wall mounted Danesmoor oil fired condensing boiler and a separate water heater immersion cylinder (Range Tribune HE). Please can you tell me the following?My house uses electricity and domestic kerosene oil for energy: - Can the water immersion heater be used on...
  7. D

    Boiler & Immersion connection recommendations please.

    Hello all I have just replaced and relocated a hot water tank and immersion heater. The two were previously connected with 14mm copper and a tap on just near the outlet of each. Obviously the taps used to be opened and closed to take hot water from either the tank or the boiler. My intention...
    • Deleted member 98304
    • Thread
    • boiler connection immersion
    • Replies: 10
    • Forum: Boiler Advice Forum
  8. P

    Immersion heater - water leaking

    I came home to find water dripping from the ceiling! After turning off the water supply I looked in cupboard housing the immersion heater but I could not find the leak - other than what appeared a leak from the immersion heater. The immersion heater is a tribune premier by IMI Water Heating...
  9. B

    Is this immersion heater washer made of asbestos?

    Hello. Whilst replacing my immersion heater, I came across this washer. Is it made of asbestos? Is there a way of telling? The cylinder must be from the 60's or 70's, but I'm assuming the heating element has been changed since then. The existing one's been in place since 2006 at least...
  10. M

    Ball valve gone? Dripping Immersion Tank

    Hi everyone! There's an annoying drip in the top tank which is constant. It's not overflowed or anything but I am concerned it will. After reading this forum I came to the conclusion it might be a faulty ball valve (simply going off what other people have said about similar issues). I have no...
  11. ChrisTanner

    Want to add immersion heater to Worcester Heatslave 20/25

    I have a Worcester Heatslave 20/25 in reasonable shape, and am about to install a load of solar PV on the roof. There will be excess capacity from the solar that I want to divert to an immersion heater to reduce the load on the oil boiler. I was wondering if I could fit an immersion heater coil...
  12. L

    Boilermate 2000 no hot water at all...not even just from immersion

    Mmm
  13. D

    Immersion heater hot water bath

    Hi, I am looking to build a DIY hot water bath, I was planning on using a small screw plug immersion heater, drilling a hole into a polypropylene tank and using a nut/gasket to seal it. Recon it could work?
  14. G

    Immersion heater/high limit stat

    Hi All How can i tell if immersion heater already fitted to cylinder has a high limit stat, important as new (plastic) CWST being fitted to replace an old rigid asbestos tank. Can post a photo of immersion heater if useful
  15. I

    Immersion Heater or Water heater

    I do not live in the UK so not always familiar with the right term. My mother has a flat in London that needs a new immersion heater to heat hot water for bathroom and kitchen.. She currently has an electric one that is very old and needs replacing. I went to B&Q, Homebase sites to look for a...
  16. L

    Help with immersion heater

    Hi I have had problem with a 3 phase immersion heater, I installed it into a gravity system about 3 months ago and it stopped working after about a month. It was installed into an existing gravity cylinder which is on bottom floor of a large office block. The cwsc is in roof space and is the...
  17. R

    External immersion heating element

    Hi I have an external thermtec geezer 3000 and it is tripping the fuse because water is gathering in the bottom cap which surrounds the electrics. I have checked and can't find a leak anywhere. Could it be condensation?? Richard
    • Richard Stewart
    • Thread
    • heating immersion
    • Replies: 5
    • Forum: UK Plumbers Forums
  18. Stanios

    Immersion Heaters...

    Hi all, In my first year I've put in about 10 immersion heaters. I've now had call backs for 4 of them that stopped working. I only put in incloy and the only two brands about seem to be tesla and backersafe. Both around £25 for 14" element. What can I do short of completely stopping doing...
  19. J

    Is there a programmable stat that can also do immersion heater?

    Hello, Looking for help with finding a suitable controller. Customer has oil Aga for central heating and hot water - simple enough. However over the summer months it gets shut down and any heat requirements are met by wood burner and hot water is produced electrically via cylinder immersion as...
  20. O

    Immersion size

    hi lads, i am just wondering if someone know she what size the top immersion has on an indirect hot water cylinder ? Will it be 14" or 27" ? I cannot see any brand or name on the old copper cylinder. It blows all the time the fuse and I would like to change the immersion it just has one...

We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.

Featured Content

Back
Top