I have a dripping shower valve. I have take away the face plate and at a complete loss at what to do. There's currently a bag sitting over it which isnt pleasing the family. Any guidance appreciated.
Hi there,
Hopefully someone will be able to help me…..
I have what I believe is a pura shower arm which has recent started leaking from the fitting which is really no wonder when you compare the weight of the shower arm (let alone the additional weight of the shower head) to the tiny female...
The first showerpump i fitted close to the immersion with warix flange and it works fine for the small bathroom.
I fitted another pump for another shower in another bathroom about 2-3 metres away and that seems fine.
i am wondering if i am likely to encounter problems later with the second...
I've installed a new shower head and hose, replacing an old Aqualisa which started to drip. The new replacement shower head which is smaller than the original also drips.
There's no leaking as expected from the new hose connections with the head or wall elbow. I've removed the cover of the...
Hi Guys.
Anyone fitted an instant water heater and could give a recommendation on a good suitable to feed a basin and shower.
Also do you need G3 to fit one?
Thanks
Not been on here for ages, got a lot of help when I installed my bathroom some years ago. Everything went fine until I had to replace the shower mixer valve recently. The old one had started to get stiff to turn, so I fitted an identical unit to make the job easy - it's a cheap, minimalist...
Hi,
We're in the process of upgrading 2 bathrooms in our house: the ensuite and the family bathroom. These adjoin one another. The ensuite is largely done so has all piping in situ. The ensuite required that we feed its soil pipe through the wall into the family bathroom, where it angles...
Hi, would be extremely grateful for any advice on the following.
I'm installing a bathroom (shower, toilet and sink) in my summer house. It has mains electricity but not water.
I've bought a power shower and a large Thetford cassette toilet.
The plan is to use water from a refillable...
First of all I have to confess I am not a plumber so please bear with me! I have a Daryl enclosed shower in an ensuite bathroom. It was already installed when I moved into my house in 2006 and was probably around 10 years old even then. The other shower components work fine, but the top shower...
Do you recognise this shower drain rubber seal? I have searched the web and common plumbing spares suppliers but I cannot find which it is.
It is from a 1990s new build en-suite shower. The plastic cover plate is silver and, when you remove it, two screws go through the fixing plate and pull...
Can anyone help
My shower is warm, but when I flush the toilet or leave the cold tap on, if gets
Hotter. The temperature I imagine a shower should be.
How to fix this. Can anyone help
Got a bath which is just over 10 years old and the shower head needs replacing.
This photo shows the layout.
I appreciate that access will be required to do this and could be achieved from the adjacent room by cutting a hole in the wall.
I’m not sure what I would then see and in...
Hi All,
Looking for some advice on my little bathroom project.
I took the bath out. I got a shower jacuzzi thing.
The base has 2 wheels in the corner.
Do I assemble the unit first attach water and elec, and slide the very heavy unit in on the two wheels? Or do I get the base in the corner and...
We have hot water, tank for hot water why is the hot water boiling hot from tap,and shower,
We are on a schedule for hot water via our hive app 2hrs in morning 2 hrs in evening
Any help be much appreciated
Pipes for thermostat shower have been fitted at different heights. Any way of rectifying without ripping all tiles. So for clarity 15mm pipes sunk into wall behind bath. Walls have fresh tiles. Have realised as about to fit shower these pipes one is set higher than the other. If you fit a...
The left rear floor corner is highest (the shower pan touches/sits on the floor), sloping down diagonally to the front right corner (lowest). The front right corner shim is 5/8", the left front corner is 3/8" shimmed, with shorter shims under left middle and right rear corner.
The pan perimeters...
IS IT POSSIBLE TO ADJUST THIS MIXER UNIT? WE HAVE TO HAVE IT TURNED ALMOST FULLY ANTI CLOCKWISE TO GET HOT WATEROUT.
THE FRONT PLATE WITH MIRA ON IT PRISES OFF AND INSIDE THERE ARE SOME PLASTIC BITS AND A SMALL CROSS-HEAD SCREW IN THE MIDDLE.
THANKS