Hi
I have noticed dripping from the overflow pipe coming from the header tank (smaller tank in loft) not sure why but I cannot adjust the ball value thing or how to. I have removed some water from the tank but there is a copper pipe which should sit in the tank but not where it feeds to
Any...
Hi all,
My mates recently bought a new old house and has had extensive work done including new bathrooms etc. We've got a few questions about the hot and cold water distribution. The house is supplied by cold water at around 3 bar, so decent enough pressure. The way it's set up at the moment...
Am I correct in saying that the capacity of an expansion vessel as written on the appliance data label is the capacity of the water compartment alone and excludes the air compartment capacity?
Thanks
Hi -
I've got a dual element E7 vented hot water system. Currently, the immersion heater at the bottom heats the tank every night - assuming minimal hot water usage, it uses between 2 and 3 kWh every night. Thing is, I don't use much hot water - I have a dishwasher and electric shower - I...
Hi everyone
I have a 20 year old Megaflo CL250 indirect hot water tank that I typically heat with an oil-fired boiler. It has locations for two immersion heaters (one at the base of the tank and the other halfway up). Only the lower immersion is installed and the other (halfway up the tank) is...
Having just moved into a property and discovering the central heating not functioning, after 3 months we eventually was able to get the property management to have one of their heating engineers attend. He was literally here 10mins and in the loft space for 2mins, where he stated he discovered...
Hi, I'd appreciate a bit of advice about my hot water and heating system..
So, we moved into a new build about 5 months ago and we have a TheraQ ProLite SS 250 unvented tank, we also have a gas boiler and Hive multizone. My understanding is that the boiler sends hot water to the tank to heat up...
Hi all
Currently have an open vent system with a 140L tank. This all needs renewing and wondering whether it was worth changing over to a high flow combi instead or to replace with an unvented cyclinder.
Currently only have 1 bathroom, but looking to add an ensuite at some point as well.
Thanks
After flushing, there is only a trickle of water entering the tank. When I turn the valve off, and then on again, it flows normally again. The upstairs toilet and all other faucets work normally.
We have a brand new house with a tank system and boiler. I had nest installed to control water and heating.
Sometimes when the water and heating times off the tank keeps on doing something.
I have to either reset the nest or turn the power off to the boiler for a bit to reset it.
Is this a...
Hi,
Trying to decide which cylinder to go for?
I am renovating my house which will end up having four bathrooms and a wc. I am planning to go for a 300l unvented indirect cylinder as currently I have a vented cylinder with a cold water tank in the loft and face issues with hot water pressure...
Hi all,
We moved into this B&B in August and I dont really understand the old fashioned system. we have one boiler for hot water and one for the heating. The tank is on the landing slightly lower than the first floor, then there is a second floor, four rooms on each floor, seven are ensuite...
I have a loft main water tank. I want to lower its height (at the moment raised higher in the loft by 1 meter to give more pressure I think) so I can put it in the eaves ready for a future loft conversion. I like the idea of a header tank for water shortages and being able to flush the loo if...
Hi there
We have had a barn renovated and the plumber installed an air source heat pump.
The hot water has been on auto since Friday and I changed it to continuous this morning but it was only 25 degrees (it’s set to 55 degrees) on the bottom of the hot water tank. The electrician came this...
I have a need for for a thermostat for a copper cylinder connected to solar power so I'm looking for an accurate thermostat which will allow me to store water at up to 90c ?
I have tried a bog standard Honeywell and a couple of cheaper stats but none of them even work up to the advertised 80c...
I installed a new electric hot water tank. They pressure relief valve keeps releasing after 2 hours steamy hot water. Replaced the pressure relief valve and the tank is still doing it. Any advice on what to do?
Hi, hope someone can help me with a heating pressure loss problem. My valiant boiler has been loosing pressure over the last few months, resulting in me having to top up the water every week or so. Managed to get a boiler engineer to visit who diagnosed a faulty expansion tank. (Water evident at...