Just can't get my head into gear tonight. Looking at upgrading an old open vent system. Thought about fitting system boiler and an unvented cylinder. But use a heat exchanger fir existing heating system. It would be wired as s plan but second pump on secondary side for heating would get feed...
Hi all. First post - be gentle.
I have added major extension to existing house. There are two pumps each supplying a separate CH and HW zone valves. The boiler is a Worchester CDi conventional. The boiler has an overun circuit that keeps the pumps runing for 3 min after the Heating demand...
Hi Folks,
I'm a Diyer so trying my hand at installing a new salus it500 thermostat on my current system
Current system
My current oil burner system is 1 zone only which heats all radiators and water together, at the boiler end I have 1 black wire and a earth going into a double switch, one for...
Hi All,
I've searched the forum for an answer to this without luck so here goes . . .
I've just replaced a Vitodens 100 system boiler with a Baxi Megaflow system boiler which is connected to an existing unvented cylinder.
I've had to fit a new 3 port valve but I'm hoping to keep the existing...
I installed the jguh1 underfloor heating system wired up the wiring centre ,does any body no if the boiler enable should have any volts passing through it when heat called for ,i linked up the unused zone vale 1 and 2 as per instructions
i tested it and nothing there between termanils and...
Hello Im after some help with a honeywell sundial wiring center. The boiler and pump are permanently on. The cylinder stat was wired incorrectly by the home owner with the common and 2 wires the wrong way round. Having corrected that I am getting 170 volts down the common and 1 wire of the...
Hello,
If a previous thermostat has been removed from a wall fixing and been made safe and plastered over, can it be dug out and reconnected?
Thanks,
Tom
Hello.
Anyone really good on Honeywell 3 ports?
Should there be continuity on any of these combinations of wires when removed from wiring centre;
Orange & grey
White & grey
Orange & white?
Cheers
;-]
I've just had to condemn an old 145L Andrews unvented water heater in a hair salon, and I am going back to fit an indirect unvented cylinder. They have a Worcester 230 combi in there at the minute which runs the heating and hot water for the kitchen sink.
I'm planning on leaving the kitchen...
I am AT LAST going gas safe next year :-) got training center sorted, lads to do my 200hours with and definitely got the customers
i i want to get away from bathroom installs and be more of a heating engineer. I have s basic understanding of hearing wiring but that's it as I specialise in...
Evening chaps got to add a unvented to a ecotec 831 tomorrow so basically running it as a system boiler and just leave the utility sink off the boiler , will freely admit to not being all up on wiring what's the crack with wiring it in all valves etc are gonna be next to the boiler cheers
Hi all, I have piped in a shower pump in airing cupboard but have no power source I can get to, also the flooring is a nightware to get up so can't run any cable that way unless no other way.
Question is can I run it off the lighting circuit ?, it already has a shaver socket in the bathroom on...
Hi all,
Just wondering how people wire these.
The installation manual
http://www.honeywelluk.com/Documents/Installation-Guide/pdf/bdr91-instal-50034510-uk07r1009.pdf
seems to have the wiring as Spur- BDR91-Boiler with power to the boiler getting passed through the BDR91 rather than...
Evening, looking for some wiring advice. Got a vokera mynute 15vhe heat only boiler. When I put the programmer (Horstmann 425 diadem) on for hw only the pump runs bringing the ch on. So basically I can't have hot water only. Anyone have any tips? There is no zone valves.
Hi guys,
my oil combi boiler was replaced. The guy who replaced the boiler may have got something wrong as the ch can be controlled indepently without the controller on the front of the unit.
if somebody could show me a photo of the wiring connections as presently my stat is like a big on /...
Could anyone advise me were I can obtain wiring diagrams for a open vented system.
the system in question would consist of the following.
two open vented boilers and a low loss header in tandem both with internal pumps and one external pump
Two water cylinders run of the two boilers both with...
Hi I want to replace an old satchwell thermostat tlx 2259 with something similar and just need to know what wire is what on my one i have just removed - heres a photo
Evening Guys
wireless thermostat has been fitted, when setting the temp the the wireless receiver powers on but the boiler does not fire up
RT24 - 24 V DC room thermostat link has been removed
The wiring has been fitted as follows 4 core cable
Mains connector block
x1 Live to stat live
x1...