Hello,
If a previous thermostat has been removed from a wall fixing and been made safe and plastered over, can it be dug out and reconnected?
Thanks,
Tom
Hello.
Anyone really good on Honeywell 3 ports?
Should there be continuity on any of these combinations of wires when removed from wiring centre;
Orange & grey
White & grey
Orange & white?
Cheers
;-]
I've just had to condemn an old 145L Andrews unvented water heater in a hair salon, and I am going back to fit an indirect unvented cylinder. They have a Worcester 230 combi in there at the minute which runs the heating and hot water for the kitchen sink.
I'm planning on leaving the kitchen...
I am AT LAST going gas safe next year :-) got training center sorted, lads to do my 200hours with and definitely got the customers
i i want to get away from bathroom installs and be more of a heating engineer. I have s basic understanding of hearing wiring but that's it as I specialise in...
Evening chaps got to add a unvented to a ecotec 831 tomorrow so basically running it as a system boiler and just leave the utility sink off the boiler , will freely admit to not being all up on wiring what's the crack with wiring it in all valves etc are gonna be next to the boiler cheers
Hi all, I have piped in a shower pump in airing cupboard but have no power source I can get to, also the flooring is a nightware to get up so can't run any cable that way unless no other way.
Question is can I run it off the lighting circuit ?, it already has a shaver socket in the bathroom on...
Hi all,
Just wondering how people wire these.
The installation manual
http://www.honeywelluk.com/Documents/Installation-Guide/pdf/bdr91-instal-50034510-uk07r1009.pdf
seems to have the wiring as Spur- BDR91-Boiler with power to the boiler getting passed through the BDR91 rather than...
Evening, looking for some wiring advice. Got a vokera mynute 15vhe heat only boiler. When I put the programmer (Horstmann 425 diadem) on for hw only the pump runs bringing the ch on. So basically I can't have hot water only. Anyone have any tips? There is no zone valves.
Hi guys,
my oil combi boiler was replaced. The guy who replaced the boiler may have got something wrong as the ch can be controlled indepently without the controller on the front of the unit.
if somebody could show me a photo of the wiring connections as presently my stat is like a big on /...
Could anyone advise me were I can obtain wiring diagrams for a open vented system.
the system in question would consist of the following.
two open vented boilers and a low loss header in tandem both with internal pumps and one external pump
Two water cylinders run of the two boilers both with...
Hi I want to replace an old satchwell thermostat tlx 2259 with something similar and just need to know what wire is what on my one i have just removed - heres a photo
Evening Guys
wireless thermostat has been fitted, when setting the temp the the wireless receiver powers on but the boiler does not fire up
RT24 - 24 V DC room thermostat link has been removed
The wiring has been fitted as follows 4 core cable
Mains connector block
x1 Live to stat live
x1...
hey guys, just been to quote for a job to replace the wiring center/programmer along with fitting a new greenstar ri.
just researching the wiring as i only really fit combis
ive noticed i need to wire the pump direct to the boiler for the pump overun - got that bit
in the boiler we have a...
Hello all.
Im hoping for some help with wiring a Worcester RI heat only boiler please.
I need to replace an Ideal FF250 P boiler with the worcester.
only thing is I only have live neutral earth in 3 core sticking out of the wall in utility room.
the rest of controls are upstairs in airing...
Went to a job today after fitting a new 15/60 grundfoss pump.. Switched everything on and it wasn't getting any current.
Long story short had to call the boss who after a few calls got quite frustrated with me as I just wasn't really understanding what he was getting me to do.
I've never...
Hi everyone
Just removed a glowworm 330 and installed a worcester 27 RI. The original wiring came from the junction box and was connected to the glowworm as follows: mains live, switch live, neutral, earth and a pump live. There is a mechanical thermostat and a Drayton digital programmer which...
Hi all,
need some help or pointers please
father in law has a system that I am upgrading. He doesn't have a room stat or tank stat.
current set up is a baxi back boiler with a grundfos ups2 pump, 3 port Honeywell valve, danfos 3020p.
so heating works and hot water works but both together, he...
Hi Guys
I currently have a combi boiler with a single prog stat wired direct to the boiler. I am putting in UFH in my kicthen diner and have to zone off using an S Plan Plus config. I have a Worcester Bosch boiler. I have drawn up the attached wiring diagram, would anyone be able to verify...