Nightmare Job

[cr0ft]

I can barely gat my finger around it so don't think a slice will go over it. I wish I took a photo before as it would be easier to come up with a plan... I'll just have to wing it.

Just made my first 2 slip couplings so fingers crossed it all goes to plan lol either that or I explain how the new water feature works to the tenant 🙂

Can you beg/borrow a Fein Multimaster or equivalent? If so cut the pipe with that then file it down before putting couplings on as required. Reaches into many places a pipe cutter can't.

Helped me connect onto pipes I wouldn't have been able to on the last job (without removing the toilet and flooring above anyway).

 

[stevetheplumber]

if all else fails use four elbows i did a leak in a ceiling o push fit that way recently only one joist width and the hep was un movable cut back to 2 inches either side elbow on each looking down and then joined from below

 

[jaydebruyne]

Can you beg/borrow a Fein Multimaster or equivalent? If so cut the pipe with that then file it down before putting couplings on as required. Reaches into many places a pipe cutter can't.

Helped me connect onto pipes I wouldn't have been able to on the last job (without removing the toilet and flooring above anyway).

What are those multi tools like, are they handy? Decent? Useful?

 

[MC_Bob]

If the pipes are so solid they can't move, it'll keep cracking fittings due to expansion.

 

[ShaunCorbs]

What are those multi tools like, are they handy? Decent? Useful?

very but you need the right blades

 

[jaydebruyne]

very but you need the right blades

What kinda blades?

 

[ShaunCorbs]

What kinda blades?

Metal for metal and copper nothing thick tho like screws else it will be a blade a screw etc, wood for wood

 

[spanner]

Cut of where accessible and run some poly all the way through and rejoin where accessible

 

[jaydebruyne]

So I managed to successfully repair the leaking joint by replacing the 22mm tee and 15mm branch.... But refilled the system and noticed another older 22mm elbow slightly leaking 🙁(((

I think I may have sweated it when soldering the tee next to it.

In order for me to drain down I'm going to have to cut the pipe.

Question: as its leaking, is it safe to assume the elbow is now loose and would come off easily?

Also, the pipe in question is next to the return which is next to the dhw supply (all 22mm and about 5mm space between them). Is it ok to solder when the pipe I want to solder is so close against another pipe? (In terms of being able to solder properly I mean).

 

[mutley racers]

So I managed to successfully repair the leaking joint by replacing the 22mm tee and 15mm branch.... But refilled the system and noticed another older 22mm elbow slightly leaking 🙁(((

I think I may have sweated it when soldering the tee next to it.

In order for me to drain down I'm going to have to cut the pipe.

Question: as its leaking, is it safe to assume the elbow is now loose and would come off easily?

Also, the pipe in question is next to the return which is next to the dhw supply (all 22mm and about 5mm space between them). Is it ok to solder when the pipe I want to solder is so close against another pipe? (In terms of being able to solder properly I mean).

Now this is a day In the life of a plumber. Any other job is boring! Constantly have to improvise we do. Well done feller for getting stuck in. Scary at first but when you have problems like this every day you realise it's part of the trade.

If it's weeping you won't be able to pull it loose. It will just be a wee bit that hasn't soldered. The others really should not sweat off as it still has water in the pipe. Unless the one that is leaking now is on the same pipe

 

[jaydebruyne]

Now this is a day In the life of a plumber. Any other job is boring! Constantly have to improvise we do. Well done feller for getting stuck in. Scary at first but when you have problems like this every day you realise it's part of the trade.

If it's weeping you won't be able to pull it loose. It will just be a wee bit that hasn't soldered. The others really should not sweat off as it still has water in the pipe. Unless the one that is leaking now is on the same pipe

Cheers Mutley, I did actually enjoy it even though it was frustrating as hell 😉 I'm quite pleased that none of my joints leaked 🙂

The tee I replaced and the old elbow joint that is weeping is on the same pipe. Maybe about 1/2 inch apart..

 

[ShaunCorbs]

Cheers Mutley, I did actually enjoy it even though it was frustrating as hell 😉 I'm quite pleased that none of my joints leaked 🙂

The tee I replaced and the old elbow joint that is weeping is on the same pipe. Maybe about 1/2 inch apart..

yea its gone thats why you always clean both sets of joints if there that close you can always add a bit of solder to an old joint just incase

 

[jaydebruyne]

yea its gone thats why you always clean both sets of joints if there that close you can always add a bit of solder to an old joint just incase

Its too late to add solder now though, but I've learned which is a good thing.. I just need to figure out how I'm going to fix it :/

I'm thinking, cut the pipe and drain down. Sweat the elbow and replace with a new elbow and new section of pipe with a makeshift slip coupling... ???

 

[ShaunCorbs]

Its too late to add solder now though, but I've learned which is a good thing.. I just need to figure out how I'm going to fix it :/

I'm thinking, cut the pipe and drain down. Sweat the elbow and replace with a new elbow and new section of pipe with a makeshift slip coupling... ???

did you get a pic? 😀

 

[jaydebruyne]

did you get a pic? 😀

No :/ but I might draw it now

 

[ShaunCorbs]

No :/ but I might draw it now

go on draw it, will help alot

 

[gassafe]

go on draw it, will help alot

You've already won the prize for most shocking pics this week Shaun.... Damned pikeys!!!

 

[jaydebruyne]

 

[ShaunCorbs]

You've already won the prize for most shocking pics this week Shaun.... Damned pikeys!!!

what i won 😀 not another padded cell visit 😀 and first day back working today 😀 might go round to check on the van a 1 am 🙂

 

[ShaunCorbs]

you got 22mm bending equ?

 

[jaydebruyne]

15mm branch leaking?

Nope, branch is now fine as it was what I replaced today.. Its the old elbow on the flow which is leaking

 

[ShaunCorbs]

Nope, branch is now fine as it was what I replaced today.. Its the old elbow on the flow which is leaking

saw the one you ment ^^ 😀

 

[jaydebruyne]

you got 22mm bending equ?

Yup, standard benders

 

[ShaunCorbs]

Yup, standard benders

i would bend it and take it out of the t and put a coupling as far as you would go without it being a pita the other end