Unvented expansion vessel pressure

[Plumbagain.]

Plumbed the property back in 2004 and was back again to move both vessels to make space for a coat rack.
No issues in 14 years apart from the big frost in 09/10 splitting a copper run to the ensuite shower and nearly flooding the property.

Does anyone know the pressure setting for a range tribune (now kingspan) unvented cylinder expansion vessel?
It says 1.9 bar on the label. But I thought it had to be matched with the setting of the prv on the inlet group? Which is 3bar afaik.

Many thanks.

 

[townfanjon]

Are you G3 mate ?

 

[Plumbagain.]

No.
I know I shouldn't be touching it as the regs are more stringent now.
It was signed off by a g3 plumber at the time.
But would be interesting to know the numbers.
That's all.
Been no issues in 14 years.
The pressure in the vessel at the moment is 1.5 bar which I checked yesterday and that's the first check its had in 14 years.
That check was made with the mains valve turned off and the hot taps turned on.

I'm not in the plumbing game now.

 

[townfanjon]

I will summon the super mod @ShaunCorbs he may tell you lol

 

[Plumbagain.]

Thank you.

 

[ShaunCorbs]

That's impossible/ very unlikely the expansion vessel has lasted 14 years without attention

My senses are tingling

You sure you haven't replaced it ?

 

[Plumbagain.]

Definitely not been replaced.

 

[ShaunCorbs]

Or depressurised and re set ?

 

[townfanjon]

It also has to be the correct vessel , they are not all the same

 

[ShaunCorbs]

It also has to be the correct vessel , they are not all the same

I may be wrong here but G3 regs weren't going back 14 years ago

 

[townfanjon]

I may be wrong here but G3 regs weren't going back 14 years ago

Cant remember when they started but my first would have been around then , ish !!!

 

[Plumbagain.]

Definitely never been touched.
You might think that another plumber has been to the property but that's not the case.

The heating expansion vessel was only replaced a few weeks ago.
Which the owner did him self. And dropped it on the pipe work below.

 

[ShaunCorbs]

Definitely never been touched.
You might think that another plumber has been to the property but that's not the case.

You've must of been very lucky and gotten one of the ones built to last (you would be lucky to get one to last past 5 years without the need for servicing)

Also they need to be serviced every year or your home insurance might not be valid if it leaks and does damage

So best to get it serviced by a G3 engy

 

[quality]

2006 for G3 I think. Nobody is bothered anyway. How many places have exploded with steam from an overheated DHWSS.
I was on a job last week that had a shower pump feeding the cold main and its been like that for 9 years.
WRAS is well behind the rest of the world.
But at least our water is safe to drink

 

[Plumbagain.]

Just got the answer on here...

I'll be back at his property in a few weeks to help him swap out his old stove and will re check the pressure and re charge.
Many thanks.

 

[Daniel Hall]

The mighty g3 engineer that is youtube......

 

[ShaunCorbs]

Just got the answer on here...

I'll be back at his property in a few weeks to help him swap out his old stove and will re check the pressure and re charge.
Many thanks.

That vid is wrong about the press but correct about doing it/how to

 

[ShaunCorbs]

Stove ??? As in gas cooker

 

[SavageW]

I like the way it tells you to replace the expansion vessel if you LDF the schraeder valve an it’s passing 🙄

 

[daWilko]

I like the way it tells you to replace the expansion vessel if you LDF the schraeder valve an it’s passing 🙄

Sounds like a new tyre salesman 🙂