Looking for some opinions on whether you should cap old hot and cold water pipes. A plumber I got to remove some old sinks from bedrooms has capped off the hot and cold pipes under the floor. I thought it didn’t quite seem like the best thing to do and thought he would completely remove the...
Hi
I have a dishwasher cold water supply that is leaking (See Photos).
My initial thought was the washer was maybe gone but looks ok.
Thought about PTFE tape but everywhere says this shouldn't be needed?
Any suggestions?
Thanks!
Hi folks
Following on from another thread I made recently, the plumber has agreed that the new cold feed he added to our loft cistern should have been lower than the existing feed to the cylinder for hot (he put them both roughly the same at 50mm) and he is proposing to put it right. In terms...
I have a 10 year old oil boiler has run well and gets serviced every year all tests are spot on, last week started locking out, would reset and run for short time, engineer fitted new control box and said thats it he was only away 10 minutes and it locked out, now waiting on new photocel, boiler...
Hello All,
Hoping for a bit of advice/info in this one:
My Setup
Small system in apartment with cold tank above hot tank in the hotpress, so fairly low head pressure. Installed a pump about 15 years ago and worked fine until last week (original pump was an Stuart Turner ST55 replaced after...
Hi everyone,
I have CH with a system boiler with a header tank and 8mm micro bore pipes to the radiators, fairly standard setup I guess. House is 1990s.
My issue is that two of my radiators are cold, while the rest are perfectly fine. Both the problem radiators are downstairs and close...
Have got hot water coming from upstairs cold water taps. Nothing has been recently changed or adjusted.
System boiler connected to Heatrae Sadia CL210 unvented cylinder.
Anyone got any ideas as to what could be causing this?
Hi, can anyone help me resolve this issue with my ideal logic combi Esp1 35.
It is making a very loud high pitched noise whenever the outside temperature is cold, when either CH or HW is being used.
For example, first thing in the morning on a cold day, run hot tap or turn up CH stat and the...
Any plumbers can advise the best way to convert the current mixer valve tap to cold water supply inlet for electric shower.
I have mixer valve tap , I would need to install a new electric shower on shower area wall .Currently is the mixer valve tap. I want to know how to do before I ask the...
Can anyone please help. We have shower issues and have had for about 2 years. We are in a farmhouse. So before hand, we would turn on our Trevi shower, it would go warm, not great pressure through the showerhead though, somewhere between normal and dripping! After a few minutes, the water flow...
My shower keeps going cold then stays like that for a couple of seconds then goes back to hot & this will keep happening the whole time while showering.
It was happening on my previous shower mixer which I then changed to the Mira one I now have & it stopped doing it for a while but now it’s...
I have a quarter turn cold water kitchen tap that has a slight drip and cannot see if the valve assembly is removed from the top? ---- there is a blue plastic cover in the top but does not seem to come off?.......... have photos of tap if anyone can help?.
One of my radiators which is the biggest one in the living room gets hot at first and I can hear the water flow but after 10 minutes the water flow stops and the radiator gets cold. It has the trv valve and I have to put it close to 4 in order for the water flow to start. The retun valve is...
Hello everyone looking for abit of advice I've got a total of 6 radiators in my house 5 are all hot but the and 1 that is stone cold ive checked the trv pin and it doesn't seem to be stuck ive bleed the radiators and hasn't done nothing I turned all other radiators valves off on both ends of...
Hi,
We have a issue with our heating, where the radiators upstairs are roasting hot, yet the radiators downstairs are stone cold .
We had a powerflush done the other day which didn't help ...Two radiators out of four (including lock shields and TRV's) on the ground floor where changed, but...
Hi experts
Fast one for ye.
Air lock on cold feed from tank in attic.
Got rid of it by cracking open nut on gatd valve.if the airlock was on the elbow just after tank connection how could you get rid of it buy opening nit instead of going into attic and cracking open elbow.
All compression...
Right, complete amateur alert...
I'm fitting a Bristan recessed thermostatic dual control shower mixer. Have fitted two elsewhere in the house without any issues. Got this one all connected and tested the water...hot is fine, nothing from the cold. When I first turned it on there was sound like...
Hi all can anyone help?
I have a Mira Silver mixer shower that is fed by a Stuart turner 1.5 twin pump that is about 6 months old which replaced a leaking pump.
The last couple of weeks the hot water is ok for pressure but the temperature has dropped to tepid at best and sometimes cold.
We don’t...
Hi all,
Quick one (I hope). I have a gravity fed heating system with a glow worm flexicom boiler in the kitchen. A tank in the airing cupboard with a Grundfos Alpha 2 pump.
For the last month or so I've had lukewarm water and no heating, have been taking advantage of the immersion but my...