Hello,
Recently moved into a new rental place, struggling with the heating equipment. I'm not a plumber or heating expert, did the troubleshoot I could think of with no success so seeking help from more knowledgeable people here.
Equipment: Vaillant EcoTec Pro 24 boiler plus Drayton Digistat+...
Hi guys. Hope you are able to help me, and thank you in advance for anyone who can contribute.
I've got a Vaillant 938 and notice that the hot water output isn't near the claimed flow. I've tested the pressure at the stopcock and it's around 3 bar. I've tested the cold flow rate from the...
Hi All
Has anyone ever questioned the reasons why Vaillant MIs for their vertical flue termination refer to damp exhaust air escapes from “channel vents” may condense in the air pipe and cause damage to the product, this would suggest that the flue terminal has to be at least 1 meter away on...
Hello
Our Vaillant boiler has developed a fault in the last 2 weeks. The hot water is working without any problems. However, within 15-20 minutes of turning the heating on we are getting the error message 'F.75 Fault. Pump water shortage'. The boiler being on for heating is pushing the filling...
Hello all,
My 1st post, here goes
My boiler has developed a funny noise that can only be described as like when you finish a drink through a straw and suck up the last bit from the bottom.. that noise?
The noise is coming from underneath the boiler and only does this when the hot water tap is...
Hi folks, hopefully someone can help as this problem is doing my head in. Sorry for the long story but just want to fill in on what’s going on.
Father in-laws boiler was dropping pressure with no sign of leaks on system. I checked expansion vessel and it had lost charge so must’ve been...
Thanks in advance. I have a valiant EcoTEC whilst the flow temp is set to 70 the heating flow only reaches a max of 45 when heating is demanded. (I can use chimney sweep mode to get to 70) but it means roads are never hot enough to warm house and boiler always on.
does this seem right?? Any ideas
Hi.
i have new installed valliant ecotec 637. The tap button is not showing on the display and the radiator is flashing on the screen. I can press the right button and change all the radiator settings but I am unable to access any of the tap settings as there is nothing on display. Please help!
I have a become aware that the boiler seems to be cycling. I have 2 zones with a programmer in the hall and one on the landing. Once the desired temperature has been reached I have noticed on the boiler panel, that when the temp drops to about 45C the boiler fires up and then when it gets to...
Hi Everyone.
I am hoping that someone could help me with a problem I have with a Vaillant Eco Tec Plus, that was fitted last year in March. When it was first fitted I noticed that it took more than 30 minutes for our radiators, to get warm, our old boiler would heat it in about 10 minutes. I...
I've got an older Vaillant Ecotec combi with a 130 Timeswitch that's broken, can the newer 150 timeswitch be used on it rather than paying over the odds for a 130? I know you can put the pins in a couple of different positions but can't remember if it fits the older ones or not.
Thanks in advance
I have a Vialliant ecoTEC pro 28 . last week or so it has been a bit temperamental ,sometimes comes on sometimes not .the answer was generally to add more water , my fill loop only has one tap to fill and that on;y fills a little ,i always remember two taps ,,anyway i get the usual F 75 and...
Hi
Hope someone could help me on this. i have a Vaillant Ecotec plus 824 boiler. i have leak ( see attached picture)
please some let me know what part it is and could it repairable?
Thanks in advance
Hi there,
Boiler question, but nothing that contravenes gas regs.
To get to the point, the Vaillant EcoTEC Plus seems to have two knobs. One has a tap symbol, the other has a radiator symbol. Even the system boiler version of this boiler has two knobs.
What I cannot make out is what purpose...
The boiler temperature is set at 70 degrees but when it fires up for heating it gets to about 45 then shuts down. The flame symbol during heating only shows two bars, out of the four. This is followed by the display of Heating Rem. off time 5 mins. And counts down before firing up again. The...
Was called out to this today. Earlier in the week the boiler had leaked and the guy had an emergency plumber out who proceeded to repair the leak, replace the PCB and charge the guy £900 to then tell him the boiler isn't working and needs a new fan. It did need a new fan (They wanted to charge...
Hi
We recently moved into a refurbished property, don't know how old the boiler is but recently all the radiators were replaced. There is a new remote room thermostat added as well.
First problem is when the thermostat says it's not calling for heat, the boiler is constantly firing up and the...
Hi guys, I'm a qualified heating engineer having trouble with Ecotec plus 615 2008 model. It's sparking and my u gauge shows a drop in pressure so it appears the gas valves opening but it doesn't light. I've checked the electrodes, door seal, condensate, burner and flue which appear fine. I'm...
Hello,
My Boiler keeps blocking with those error code on display
I saw somewhere it should be an issue related to the mainboard.Can anyone confirm or advise on any extra checks to do?Thanks
Hi guys,
After some advice on above please. So I’m carrying out a safety check, isolated the above underneath, lost count after 14 attempts to ignite. Pcb?