Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

fittings

  1. S

    Are any solvent fittings available?

    Hi, I am at present doing a project (not plumbing). I need to connect 15mm copper fitting to either 50 or 40mm plastic pipe. Does anyone know of a solvent adapter available, as I can't find one. Many thanks. SMB
  2. Bogart

    Solder ring fittings

    Not had need to do any solder ring fittings for a few years now. Recently have done a couple of lots last today where I, like previous attempt, could not get a ring of solder to appear. My technique is the same. The joints do not leak but I do like to see the solder ring as it gives me...
  3. L

    DIYer updating plumbing fittings in cloakroom toilet - Help needed

    Hi Guys We've recently moved and are in the process of updating the cloakroom toilet. I've taken the sink out and there's pipes attached in multiple ways. Could someone suggest which modern pipes and stop-taps I need to replace what I've discovered in order to fit the new sink? Photo...
  4. S

    Thoughts on jointing compound for compression fittings?

    Would you recommend using jointing compound on newly installed compression fittings? Some say use it always while some say it affects integrity of joint.
  5. B

    Concerned whether KX(?) Solder ring fittings safe for drinking water?

    Hi, first post :-) Purchased a number of fittings today and long story short, after being referred to as Yorkshire fittings over the counter, I suspect this was a bit misleading?. How do I know if the solder ring fittings purchased are a) safe for drinking water (and b) presumably, if that...
  6. P

    Please help find these fittings

    Quick story, our fridge hasn't been connected up to water for awhile. Went to get the fittings but they was not all there. Now i'm unsure where to find the fittings in the pictures. Obviously i have one side but i need the same fittings for the other side. So if any one could point me in the...
  7. Scott_D

    Best fittings for lead

    I need to replace some lead water main in a house thats being renovated Its approximatly 20mm OD What are the best fittings to use? Lead Loc or a universal fitting like plasson or philmac?
  8. Z

    Rinnai Infinity 16i gas water heater - no boiler fittings

    Hi, just purchased a Rinnai Infinity 16i gas water heater from Mr. Central Heating. Boiler and flue arrived but fittings are missing. Its got 3 x 1/2 BSP brass male connectors coming out of boiler. What's needed and where do I get it from? Gas installer advised that these should have come with...
  9. S

    Yorkshire fittings help

    I decided to try Yorkshire fittings on the new kitchen build. Normally with me being a novice I used compression fittings in the past. So with the Yorkshire fittings I watch how its done on You tube. Easy I thought, how hard can it be???? So I bought all the gear and stated to follow the you...
  10. E

    Pipe coupler issue - connecting two male fittings

    Hi there I'm trying to connect two male 15mm x 3/4 inch pipe connectors together. Can anyone advise the adapter I need and where to buy it from? The problem is shown below. Note: This issue occurred because I am trying to tee off from the kitchen cold water pipe to supply an outside tap...
  11. bright spark

    Making compression fittings in tight spots

    Does any1 have any neat tricks for working on compression fittings in tight areas. Does any1 use any ratchet spanners etc or just take lumps outa your fingers. i know push on fittings are a god send but can't b used on gas. thanks
  12. N

    HPB15 fittings

    Hi, Got two pipes, 1 hot & 1 cold feed that I need to permanently stop off. The pipework is grey plastic & the fittings say HPB15 on them. Has this been superseded by HEP 20 ? If that's the case can I simply use the HEP 20 blanks? Thanks
  13. R

    Plastic tee fittings near boiler

    Hi, i'm installing a bathroom and need to install tee fittings into existing hot/colds. The best place to do this is near the boiler, however someone told me you cant use plastic pipe/fittings within a certain distance of the boiler. The best place for the tee would be about 2 feet away from the...
  14. D

    Replacement Three Way Valve - Including Pipe Fittings

    Hello folks. I need a replacement 3 port valve for my central heating system. The current unit I have is a Siemans / Landis & Staefa RHM mid port 3 way valve. This one: heatingsparescentre.co.uk/siemens-c25/motorised-valves-actuators-c3028/siemens-rmh-2-3-port-spring-return-actuator-p22514 I...
    • davehart
    • Thread
    • fittings pipe replacement valve
    • Replies: 11
    • Forum: UK Plumbers Forums
  15. M

    What size pipe insulations fits over 42mm compression fittings?

    Hi, All in the title really, What size pipe insulations fits over 42mm compression fittings? I don't have one at hand but need to place an order for some pipe insulation. Im thinking 54mm but not sure. Cheers!
  16. E

    push fit fittings on unvented cylinder

    looked at an install today and the pressurised cylinder cupboard ws completed in push fit. The tundish hadnt been conected yet but wht are peoples views on it. i personally only use copper but am told plastic is ok. Eddie
    • eddiebrown424
    • Thread
    • cylinder fittings unvented unvented cylinder
    • Replies: 4
    • Forum: UK Plumbers Forums
  17. M

    Polyplumb fittings

    I have a grey polyplumb elbow that I need to remove one of the pipes from to replace it with a longer length. I assume ideally I would use one of the component kits on the new piece of pipe, however, I have a new unused straight coupler and I wonder if it is acceptable to take the end of one...
  18. J

    15mm glued Plastic pipe & fittings

    Hi Guys Hoping someone can help. Came across a house in Devon completely plumbed with glued 15mm PVC type hard plastic pipe. (The lady wanted a basin replacing) The tap connectors were brass/copper imbedded in a plastic pipe connector, the pipe and fittings are white, with '15mm made in uk'...
  19. I

    Installing plumbing fittings so they are removable on unmovable copper pipe

    Is it possible to install compression valves onto existing non-pullable copper pipe WHILE designing-in a means of being able to replace the whole valves should they fail? Hello, I have existing 22mm copper pipe that needs a small section cutout to install a compression isolation valve...
  20. Chalked

    Plumb Center copper fittings

    Who makes thier end feed range? They are reasonably priced, but one end will be tight and needs thing on and the other side is slack! im going back to yorkshire endex. Rant over :censored:

We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.

Featured Content

Back
Top