Hi All,
Problem with a GW 18HXi reporting error F13 (PCB Fault). I've replaced all the electrolytic capacitors on the PCB, many bulging with high ESR. After reassembly the fault remains. Swapped board with a known good one and the fault remains.
Any ideas?
Hi everyone.
When I looked in the cupboard where our gas combi boiler is installed, I found a wee white plastic cap which had pretty much disintegrated. A search found it was the cap that's meant to seal off the flue test point - from which a nice breeze from outside was ensuing.
As it...
Hi,
I inherited the above boiler when we moved house about 3 years ago and it has never given me any trouble until now.
In the last few weeks we have noticed that the heating is not coming on every now and again and when I look at the boiler the reset light is on.
We realised that our 18...
Hi
I inherited an LPG burning Glowworm 30HXi when I moved into my house some years ago.
Great little boiler but had been neglected. I cleared a lot of debris out of the heat exchanger and chamber at base, on top of the condensate trap.
I always flush several litres of water through the trap...
Hi there
Today friend was changing radiator valves, so he drained system, put radiator valves, new radiator.
I notice TRV valve was on cold end- return or out line from radiator.
I asked my friend to relocate TRV valve on inlet side. (when heating started, hot water was coming from white plastic...
Hi
I have a Glowworm Micron 40FF and it fires up ok but then trips out after a little while with the two LEDs alternately flashing.
The thermistor value is ok and the OH stat switch is closed
The manual says this is a software sequence error so I thought it was a PCB fault
However I have now...
Hi, after some help with a flexicom 30 CX - 9 Years old.
Pressure slowly creeps up toward 3 bar, followed by a very slow drip.
Plumber has been out & done the follwing:
Represurised expansion vessel
Relpaced plate heat exchanger
confirmed both filling loop valves are passing water.
Plumber now...
Hi all
Am fitting one of these next week. Made a start Friday and hung it on wall.
In the box you get a TMV blending valve and a Caleffi branded combi bloc for the unvented side of things.
The book tells you nothing!
I have sussed it I think but just have one question. The combi bloc has a...
Hello
I have the above boiler in my new property. Was only built a few months ago so brand new.
To get to the point before I call Glowworm out under warranty, I know their aftersales are shocking.
The boiler when lighting is occasionally making a really loud rumbling noise. To the point where...
The pilot light will not stay on my Glowworm Hideaway 80B. I have replaced the valve, the thermocouple, ensured all gas pipes are clear of blockages. I have electrics to all plugs. I can't see anything further I can do to solve this issue. Can anyone help?
Hi,
I have a Glowworm flexicom fitted in my house and like most it has an issue where the pressure sensor gets clogged up and you need to increase the pressure or you get an F9 fault.
Basically, every few years it needs removing and cleaning.
Recently I have notice that there is a tiny leak...
I wonder if anyone can help. I moved into a 12 year old 3 storey house just over a year ago. The heating and hot water worked fine all last winter. When I have come to switch it on again now the weather is colder, the hot water is fine but the radiators don’t come on. I turned off the hot water...
Just fitted a gw18 home. all fires up, only way to get heating is to manually move the leaver on 3 point value, programmer is not connected any ideas on wiring it?
old boiler was glowworm 18 sxi with pump in airing cupboard.
this has been removed as the gw18 had the built in pump.
Thanks
Just looked at glowwworm essential 24c combi. Only 14months old and out of warranty.
Hot water will only run luke warm.
Temp coming from heat exchanger only reaches about 45c in hot water mode.
Super red hot in heating mode no problems there.
Checked thermistors which control both heating and...
Glowworm 100ff wall hung 30kw conventional boiler. Set up in garage with correct 28mm runs to rest of system. All worked well over the years odd new bits and bobs. Recently serviced It goes through start up sequence fine style.
Call on from timer in house, fan starts, pump on, starts ignition...
changed expansion vessel and put external filling loop as crappy internal one nackerd now not even showing a fault code and pressure wont go above 0.5 bar no flame nothing any ideas?
hi there,
Recently my boiler started making a loud buzzing noise. The noise is intermittent, and sometimes goes off if I turn on the central heating or hot water.
I’ve had a homeserv engineer come over for a health check and he said it was a faulty (PCB). Part no: s900847
I wanted to get...