Hope you confirm something’s for me, boiler calls for how and ch but am not sure if pump is rotating, have checked if it’s stuck via inspection cap on pump which is ok. 240v at pump and on pcb so that’s ok. Can someone tell me how I check if it’s rotating, if not it states drain primary circuit...
Dear Professionals, could you please advise. I have standard mixer tap in my bath (its about 15 years old, i recently bought the house). The water comes out from tap itself in massive amounts, bath can be filled in 3min, same if i unscrew shower hose - the water will shoot up very high, however...
Hi there,
Hopefully someone will be able to help me…..
I have what I believe is a pura shower arm which has recent started leaking from the fitting which is really no wonder when you compare the weight of the shower arm (let alone the additional weight of the shower head) to the tiny female...
I've installed a new shower head and hose, replacing an old Aqualisa which started to drip. The new replacement shower head which is smaller than the original also drips.
There's no leaking as expected from the new hose connections with the head or wall elbow. I've removed the cover of the...
Hi I want to replace my trv heads on my radiators. However I am trying to find what the current ones are as they seem different to the typical screw on ones. These ones clip on with a spring loaded thumb turn. There is no thread on the inlet fitting to the radiator either. Any idea what I need...
First of all I have to confess I am not a plumber so please bear with me! I have a Daryl enclosed shower in an ensuite bathroom. It was already installed when I moved into my house in 2006 and was probably around 10 years old even then. The other shower components work fine, but the top shower...
Got a bath which is just over 10 years old and the shower head needs replacing.
This photo shows the layout.
I appreciate that access will be required to do this and could be achieved from the adjacent room by cutting a hole in the wall.
I’m not sure what I would then see and in...
Good afternoon,
I am after a replacement British Gas TRV head. I have found a direct replacement on Ebay, however they are £39.99 + £3.99 postage.
Does anyone know if there is a different TRV head that will work?
Kind regards,
Laurence
Hi,
I was hoping someone might be able to help with this. The tap is a Bristan RS BAS C, the hot tap has been leaking and I've trying to get the tap off to clean the cartridges, but cant get the sphere at the end off there. Looking at the diagram, it seems that you should be able to pop the...
Mira shower head.
Does anyone know anything about this shower head (I will post pics)
Its gotten a bit dishevelled, does it come apart easily & then just unscrew to replace with a different one ?
Hey, here goes and I hope it works.. never used one of these before!
I have a Sagittarius Ergo mixer shower min bar of pressure required 1 bar.
Connect to this is a 1.5 bar Ora Salamander pump for a positive head, this was connected by a plumber of course and we’ve had it all rigged up...
Been getting large amounts of sediment coming through the electric shower.
Had two plumbers look at the job who are unsure of how the sediment can be getting through to the electric shower. The electric shower is run off the mains not from the cold water tank. Any ideas on how this has...
Greetings, esteemed community members,
I find myself in possession of a remote and highly inaccessible plot of land, devoid of any utilities. On this land, there exists a well housing a 10-year-old pump that has never been utilized. I intend to conduct a thorough test using a portable...
Has anyone seen tap heads like these? Trawled the internet cannot find anything similar, after removing the grub screw I cannot for the life of me lift the tap head off tried prying with screwdriver but too scared to use excessive force and break the tap
Hi, i have a dripping hot tap on Bramham mono sink basin. I’ve replaced washer several times and can’t remove the tap head to deal with the cartridge. It is a screw cap cover but no additional screw underneath to release tap head. Thankyou
Hoping someone can help, not even a novice. In the bathroom there is a rainfall type shower head. I need to clean it. It is square and fitted into the ceiling and not sure how to remove. There is a 5mm gap from ceiling. Not tried unscrewing yet
Have a Grohe shower head and struggling to find connections from this to my hot and cold supply pipes…. They fit 15mm threads but the thread is deep and the surface is not flat so am worried about the seal
Hello forum, 1st time here.
The Grundfos 3-speed pump in a Worcester Heatslave 15/19 oil combi boiler is on its way out.
The boiler is old but in v good nick. The network is trunk/branches. All rads (but one) have TRVs.
Pump is set on max, which seems to be what it needs when supplying all...