Does anyone have any ideas how to get to the seat washer on this tap that is leaking badly at the spout. I'm assuming the gland part unscrews from the spout but I've tried this with condserable force but with no luck. I'm assuming the spindle is secured in and does not pull out.
Any guidance...
my shower works fine from the multi point the hot water comes from the hose and runs ok till i turn the shower off, however as soon as i fit the shower head to the hose the hot water cuts out after a minute or two then relights then cuts out again . new diaphram fitted but the problem still not...
Hi plumbers and DIYers
I made a post about my 3-port valve a couple of weeks ago, but have finally been able to take a look and thought best to start a new one than tag on. Hope that's ok.
Recap: We've had a problem whereby our boiler will only heat the radiators, even when set to hot water...
Please can someone advise, just had a two port valve head installed. When I turn heating and hot water on the valve lever automatically goes to manual. With the heating and hot water off I cant move the lever into manual
Morning,
I have an issue with my bath faucet. It used to work fine, but all of a sudden when I run the taps, no water comes from the main bath faucets.
All water goes straight to the shower head, despite the diverter not being on.
Any ideas?
thanks
Hello Everyone
I am replacing an all in one shower arm and 200mm square showerhead a head has fallen off and I had to remove arm.
I want to replace with a 300mm head like this.
https://www.NoLinkingToThis/p/cooke-lewis-adjustable-ultra-slim-square-shower-head-chrome-300mm/5882t
I have now been...
Situation: Had a boiler system conversion. From Potterton boiler with Gledhill storage tank with on demand hot water to Veissman Combo with on demand hot water. 2 bed semi with only myself and wife living here. Unfortunately used iheat service which has no real customer service. Have had the...
Morning,
I have this old shower head in a newly acquired house, and am trying to find a replacement shower head. Doesn't need to be the same design, but just trying to make sure the connector is the same as a new one.
I found an identical head online:
But in one question the answer is its 7/8"...
Hi guys
trying to install a tado trv but struggling to install it even with the supplied extra bits, I wanted to know the type or name if this valve head? Can anyone kindly help
thanks
hi all
so, currently i have a rear feed shower arm and a rainfall head. is there any connector or elbow we could replace the arm with, that would enable us to connect a handest shower head instead?
Hi,
Found some great answers here but first time posting, go easy on me please 😋.
Looking to fit a salamander rp50tu shower pump to a gravity system. It's a 'universal' (negative head compatible) pump which will be going in the loft (2 story house) just below the bottom level of the cold water...
Hi, I am trying to replace the washers in a 1960's bathroom that has BBC (Barking Brassware Company) basin and matching bath taps fitted. Having difficulty in working out how to remove the tap handles that resemble a very chunky 4 pointed design. There's a small grub screw on one of the 4 sides...
Hi everyone,
I have a thermostatic pressure shower in my bathroom and a found flow reducing valves similar to the link provided.
I would like to know what is the purpose of these and if I should pop one in the shower head as I opened the shower head and nothing was in it, the flow...
I updated an old TRV3 many years ago by using the TRV4C conversion kit including replacing the black plastic locating ring fitted in the top of the body with the support ring in the pack.
As the head has broken can this be replaced with a TRV4 head or do I need to buy another TRV4C conversion...
Following on from my previous I have now received my Bulldog Thermostatic Valve Head as pictured below and removed the previous ring however I am finding it hard to find the position for it to slot into place and turn the ring to fix into place - any advice for a extreme novice like me?
I have snapped the head off my bulldog the thermostatic valve - are the heads interchangeable with other brands and will they be able to easily replace if the pin looks like so?
Hi,
I've got a Drayton Thermostatic Head that is totally stuck on 0, i.e. can't twist it round. I've taken it off the radiator and it still won't twist at all, it's almost like it's locked somehow. Is there an easy way to free it? Thanks in advance.