Hi there, i have a customer with said water heater and was wondering if any of you know why it may just be running warm? Im not the cleverest around fixing boilers ..thinking it may be the high limit stat maybe? Any knowledge welcomed guys.
Hi.
The PCB on my gloworm 35CI broke P/N 801915 and the updated model for this is now P/N 2000802038.
On changing the PCB, the old PN had a H6 pin which went to the controls board. The new card doesn't have a H6 pin but has a H9 pin instead.
Not wanting to bust the board I haven't...
hi
I live in a 5 storey ex-council block. the apartment's water mains is leaking and the pipework is too short to freeze. access the manifold for the floor would require scaffolding. so, it looks like I need to shut of the water to the building for a few minutes while we swap my apartment's...
Hi everyone, my next predicament. I've got a Main Combi ECO 25 - no CH, DHW works fine.
I've just replaced the Motor valve - no luck!
Next the whole 3-way Diverter valve? Is not that then what else?
There is no room stat attached.
Any advice is much appreciated.
Is this the boiler that the new condense traps font have wires on?runs fine with the wires of but locks out when in place trap was full and there's a problem with the waste which I will sort but even with trap empty and wires on it locks out
Hopefully someone will be able to give me a web link to the particular regulation.
Just had a new kitchen fitted, the tap is a Brita Ceto filter tap. This type of tap is a single channel tap, ie the hot water and mains cold water mix within the spout. The instructions for the tap state that...
So, I'm having an issue with this reoccurring E133 fault on this boiler installed only three months ago.
Initially it was locking out after four attempts of lighting with E133. Sometimes it would light but with explosive ignition.
Looked on previous posts for advice, and have checked the...
Got an old main 24he on its way in my house. Bought a main 25 e co elite on black friday from william to replace it.
Do they use the same jigs as all the other baxis etc
Anyone else fitted these and have any opinions on them? Fitted my first one today and I really like how most of the bits you might need to check and service are actually on the outside of the case such as the PCB, condensate trap etc.
Will be fitting them again!
Hi all
Hoping somebody can help and maybe do the job. We are wanting a new combi fitted but the water flow is not enough from main. We have rang several contractors that do moling as we did not want ant major digging. We live in a terrace with a passage up the middle but there are drain lines up...
Hi guys
Does anyone have any experience of these boilers? I have hw which is fine and ch fires but will only stay on for 30 secs... Temp gets up to max then flame goes out and boiler overruns as the heat isn't getting away! I've changed the pump and baxi have been no help.. No pressure issues...
Hi guys
I wonder if anyone could please shed some light on this issue...
Main 30 HE combi fine on HW, and CH fires but very quickly reaches max temp (80) iirc
Baxi tech help went much help tbh, stating the bloody obvious as usual (restriction, etc)
I have changed the pump, which made no...
Hi All,
i am looking at a Main 30 HE combi that is struggling to get going. It does after a few attempts fire up but as soon as it gets going and lights the burner the main rcd on the consumer unit trips. I am looking at changing the board. Has anyone had anything like this before and if so what...
I've just moved to a new house and I noticed an overflow leaking from the loft.
In the loft I can see the main cold tank is overflowing and there are two ballcocks installed in the same tank, one of which is leaking.
Luckily each has an isolation valve, so I thought as a quick fix I would just...
Hi everyone! I'm doing up my bathroom and we've had a leaky roof fixed, so I removed all the soaked water pipe covers to reveal the green pipe underneath. I dried it out but noticed that cold water has surfaced very quickly. The pipe is very cold. Is this normal? How do I check if the pipe is...
I was at a customer's house today and came across an old stopcock on an iron rising main. The main won't last for ever, but replacement is not afforable for customer at present.
The head has been forced, thus damaging the spindle.
It would be nice to be able to fit new headgear in this sort...