Heating Bangs when switching off.

[Paul Cooksn]

What speed is the pump on now?

Pump is on 2 as the system is quite large 12 rads.
Cheers.

 

[Last Plumber]

I

Pump is on 2 as the system is quite large 12 rads.
Cheers.

If it works well it's fine. You want them on the lowest setting that works and gives the right flow and return temps.

With the valve:-
screw it shut, turn on the heating and hot water so both Motorised valves are open and the pipes start to get hot. Slowly open the Auto by-pass 1/4 turn at a time, (a few seconds in between turning), until you feel hot water flow through the by-pass. Then close it back around a half turn.


That's the best explanation I can give on a Forum. I would be going to greater lengths to set things up and balance the system if I were doing this in person but it will do!

 

[Paul Cooksn]

I


If it works well it's fine. You want them on the lowest setting that works and gives the right flow and return temps.

With the valve:-
screw it shut, turn on the heating and hot water so both Motorised valves are open and the pipes start to get hot. Slowly open the Auto by-pass 1/4 turn at a time, (a few seconds in between turning), until you feel hot water flow through the by-pass. Then close it back around a half turn.


That's the best explanation I can give on a Forum. I would be going to greater lengths to set things up and balance the system if I were doing this in person but it will do!

Thanks I'll do it on Saturday and let you know how it goes.

Cheers.

 

[Last Plumber]

Thanks I'll do it on Saturday and let you know how it goes.

Cheers.

Please do come back and tell us how you went on.

 

[Paul Cooksn]

Please do come back and tell us how you went on.

Hi.

I fitted the valve where suggested and unfortunately it still bangs, perhaps even louder. I can't get water to run through the valve unless I restrict the hot water flow, even with it turned down to 0.1 bar, the lowest it will go.

Picture attached.

Cheers.

 

[Ric2013]

Does the light on the pump flash or stay solid?

 

[Paul Cooksn]

Does the light on the pump flash or stay solid?

Stays solid then switches off completely.

Cheers.

 

[Ric2013]

Okay. That's fine. If you were running it in flashing mode, then it would not be running fixed-speed, and the automatic bypass valve wouldn't be able to work as it should.

 

[Paul Cooksn]

Okay. That's fine. If you were running it in flashing mode, then it would not be running fixed-speed, and the automatic bypass valve wouldn't be able to work as it should.

I'm not sure it is. I can only get water to flow through when I restrict the flow on the hot water.

I would have thought 0.01 bar would be open all the time. Any suggestions.

Cheers.

 

[SavageW]

When you say restrict the flow on hot water,is this when the system is running eg demand from heating/hot water? The hot water coil should have a balancing valve on it that should be restricted (which from the pic you have one after the 2port) to stop the heat just whizzing around the coil and giving less to heating

 

[Paul Cooksn]

When you say restrict the flow on hot water,is this when the system is running eg demand from heating/hot water? The hot water coil should have a balancing valve on it that should be restricted (which from the pic you have one after the 2port) to stop the heat just whizzing around the coil and giving less to heating

The balancing valve is fully open. When I mentioned restricting the flow I shut it off. Are you saying this valve should be half turned off or similar. Is this likely to contribute to the banging.

Cheers.

 

[SavageW]

It should be restricted yes,but are you only getting flow through the by-pass valve when there is still demand for ch or hot water an your closing the balancing valve?

 

[Paul Cooksn]

It should be restricted yes,but are you only getting flow through the by-pass valve when there is still demand for ch or hot water an your closing the balancing valve?

If I run the water and heating separately or even both of them together I can't get any water to pass through the bypass valve. I can only get it to pass through when I close the balancing valve with the hot water on demand.

 

[Paul Cooksn]

Another point I forgot to add. If I turn the pump off at the fused spur, it doesn't bang. Don't know whether this has any bearing on the fault but thought I would mention it.

Cheers.

 

[Last Plumber]

What size of pump is it, I can't read it

 

[Paul Cooksn]

What size of pump is it, I can't read it

Photo attached. Cheers.

 

[Last Plumber]

Nothing unusual about that size.

 

[Last Plumber]

You don't really want water passing through the bypass when the valves are open so I wouldn't worry too much about that if the flow and return temps are ok at the Boiler.
I'm surprised it still bangs but you do need to rule things out like the lack of a by-pass before you can start to think of other possibilities,

I'll put my thinkin cap back on.

 

[Paul Cooksn]

You don't really want water passing through the bypass when the valves are open so I wouldn't worry too much about that if the flow and return temps are ok at the Boiler.
I'm surprised it still bangs but you do need to rule things out like the lack of a by-pass before you can start to think of other possibilities,

I'll put my thinkin cap back on.

Cheers, it seems to be dragging on this but any suggestions I will try and I really appreciate all the help and advice.

Flow and return seem normal and all radiators get nice and hot.

I even tried balancing the system by restricting flow in the first radiator to warm up and so on.

I tried refitting the bypass valve with a normal 22mm isolation valve which I fully opened and it still banged. This would suggest an auto bypass is not required or not working even though the water is passing through and the pipes are hot.

When I am bleeding the system, when there is air present it doesn't bang. It's only when all the air is removed it starts to bangs.

Could the system just be full of glag as the filter is really dirty every week with bits of swarf/metal in it.

Thanks again.