Newbie on site....hand tools help.

[malcky]

Hello all, new to the site and also to the plumbing world and in college after nearly 20 years in office work and fancied a change of career.

So looking for a wee bit of assistance getting the best hand tools needed for my new chosen career.....Only hand tools for the time being as the budget wont allow it for now while im studying at college....I will do another thread for power tools when the time comes.

If people could let me know of the most common and best tools to start the ball rolling, I dont want the cheap everyday stuff as dont mind paying for good quality items, even if they are pricey.....(buy cheap buy twice or more)

My shopping list so far is:

Spanner sets...do I need imperial and metric? seen a nice Bahco set which is metric.
pipe cutters...Bahco ones again look good.
pipe benders...Rothenberger was suggested by my tutor.
Wrenches....What sizes are the most common everyday ones people need or use...6", 8", 10" etc
Blow lamp....Rothenberger super-fire 2

This is just the start of many tools I will get, so please list any other good quality brands too for anything I should be looking out for.

Thanks folks.

Malcky

 

[Billy Bob Bob]

Spanner sets...do I need imperial and metric? seen a nice Bahco set which is metric.b
bacho evertime
pe cutters...Bahco ones again look good.
there not,kopex or monument
pipe benders...Rothenberger was suggested by my tutor.
hes not been plumbing long enough then hilmor,but the older type theres a seller on the bay doing refurbs
Wrenches....What sizes are the most common everyday ones people need or use...6", 8", 10" etc
you mean spanners,22mm for rad tops,16mm for trv tails also buy a ratchet hex tail tool

Blow lamp....Rothenberger super-fire 2
yep,best you can buy

Read more: http://www.ukplumbersforums.co.uk/p...ewbie-site-hand-tools-help.html#ixzz28H2UPQkg

 

[Subby]

Get a good pair of grips (pump pliers) - Vise grip recommended; and a pair of long reach screwdrivers, although I am yet to find ones of good quality (I hear good things about Snap-on and Wiha).

 

[malcky]

Thanks guys, so Bahco gets the thumbs up for spanners/wrenches...probably safe bet for the pliers too im guessing? Lamp choice is good, will look into the Hilmor brand for benders....any other tools I should be looking out for?

 

[tamz]

Hello all, new to the site and also to the plumbing world and in college after nearly 20 years in office work and fancied a change of career.

So looking for a wee bit of assistance getting the best hand tools needed for my new chosen career.....Only hand tools for the time being as the budget wont allow it for now while im studying at college....I will do another thread for power tools when the time comes.

If people could let me know of the most common and best tools to start the ball rolling, I dont want the cheap everyday stuff as dont mind paying for good quality items, even if they are pricey.....(buy cheap buy twice or more)

My shopping list so far is:

Spanner sets...do I need imperial and metric? seen a nice Bahco set which is metric.
You'll rarely use them so buy a set at a fiver on ebay (metric)
pipe cutters...Bahco ones again look good.
Looking is not working. buy Kopex or Monument
pipe benders...Rothenberger was suggested by my tutor.
Hilmor or Bend it Now. If your tutor was good on the tools he would still be on them.
Wrenches....What sizes are the most common everyday ones people need or use...6", 8", 10" etc
Bahco wide jaw and knipex alligators or cobras. 6 and 8" on the spanners and 7 and 10" on the grips
Blow lamp....Rothenberger super-fire 2
You got that one right :smile:

This is just the start of many tools I will get, so please list any other good quality brands too for anything I should be looking out for.

Thanks folks.

Malcky

I hope you have deep pockets :wink:

 

[tamz]

Get a good pair of grips (pump pliers) - Vise grip recommended; and a pair of long reach screwdrivers, although I am yet to find ones of good quality (I hear good things about Snap-on and Wiha).

CK for yer long drivers

 

[Best]

Also check out Footprints - 7" & 10" ones. Takes a while to get used to them, but they are very compact & versatile & become part of your hand.
Hand bender 15 - 22mm, though not as good to use as a frame bender, will be a cheap, easy carried bender. Hilmor may be best. Record did similar & it was great.

 

[tamz]

^^i agree^^
A set of 9" footprints are the best buy you will make. You may not use them everyday but they just do what it says on the tin and will get a turn when nothing else will.

 

[malcky]

Ok cool, settled on the kopex or monument cutters, hilmors for the benders, super-fire 2 lamp, 6" & 8" wrenches + 7" & 10" pliers from Bahco, have already got a set of Wera screwdrivers but will add long reach to the list.....anything else that are must have hand tools?

As for deep pockets....well its like everything you start from scratch, its always expensive starting out and thats why im not going to get cheap stuff and then replace after a few months use.....want good reliable and hopefully years of use.

 

[malcky]

Dont think I have ever seen...defo not used footprints before but will check them out too....

 

[Best]

Sandvik 244 hand saw (Bahco) is hard to beat & cheap. The Baracuda one is slightly dearer but has a thicker blade. They last for ever if you don't let them rust & don't cut grit & steel nails with them!
A good set of ball ended Allen keys essential also. Just a 9 piece set up to about 10mm will do wee things.
A decent claw hammer & a nice thin bolster not to be overlooked as you need these for floors etc.

 

[tamz]

hilmors for the benders
Have a look here for a bender
Hilmor GLM Hand Pipe Bender Refurb Superb Condition BARGAIN | eBay
These are NOT refurbs. they are made by the co who made hilmor before they shipped out for the cheap labour

As for deep pockets....well its like everything you start from scratch, its always expensive starting out and thats why im not going to get cheap stuff and then replace after a few months use.....want good reliable and hopefully years of use.

If you stick at this long enough you will spend more on tools than you did to buy your house!

 

[Best]

Don't rule out cheaper hand tools. Some are very good quality & if you lose them you don't mind the small cost. I have a 15" adjustable spanner (the better bare metal type that is identical to Bahcos). It says "made in China" on it & that was years ago when Chinese stuff was frowned on. It cost a fiver & is very high quality!

 

[tamz]

A decent claw hammer & a nice thin bolster not to be overlooked as you need these for floors etc.

The ONLY decent claw hammer is an Estwing.
The thin bolsters are called feather splitters or a 2 1/4" electricians bolster (i've yet to see an electrician who could use one).
The best ones are made by Eclipse

 

[malcky]

Wow helpfull folks on here and what a good deal on the hilmor benders...just ordered them now...will get some good practise on them (need to see about scrap copper though) Suppose some cheap stuff might suprise you if been made well.

keep the suggestions going folks. thanks

 

[tamz]

Good choice. Miles better than a rebranded cheap import rothenberg.
You will see when it arrives on Friday or Saturday. These are the real deal. If they refurb them i've yet to find where.

 

[Mike Jackson]

For screwdrivers Halfords professional take a lot of beating. Their long reach screwdrivers are the dogs and the two that I use the most.

 

[kay-jay]

Great advice here. Only thing i disagree with is the superfire blowtorch. I have one and seldom use it unless on 28mm.

It is ruthlessly efficient but flame is too wide to train on a small area and I've burned through lots of heat mats.

I went back to using my bernzomatic can't fault it and flame has more of a tip to it. In many instances i don t even need a heatmat whereas i would with the superfire

Sent from my GT-I9100 using Tapatalk 2

 

[Harryplumb]

For spirit levels make sure its either stabila or stanley fat max. Scaffolders, 600mm and 1200mm should be the ones you require. Bahco hacksaw and files, estwing hammer. can't go wrong with a nice 3' crow bar either!

 

[Kyle87]

Knipex cobras are awesome. And you can get them for 20 quid on flea bay.
I find the monument red/yellow pipe slice good.
I use it when I need to slice only a few mil off the pipe and as this pipe slice hugs round the entire surface of the part you are cutting it helps not to deform the pipe like your other pipe slices will. Found it very handy fitting trv's when the new valves were a touch bigger than the last ones.