Hi Everyone, I’m new to this site so not quite sure how it all works or if this is even in the right place but here goes.
I live in a large property that used to be one of the training centers for Lucas Engineering. However it has since been converted back to a residential dwelling.
The house...
Hi guys. I’m on a job at the moment where the building has 100 flats over 4 floors. The problem is there’s no mechanical supervisor on site or any drawing in regards to the waste pipe work. One of the issues seems to be, there’s only 5 vents going out to atmosphere. today we’ve been told to run...
We have a Grundfos for a domestic water booster application. Everything is set up for constant pressure, discharge pressure sensing and all appears okay, except we cant get the motor to run in "auto". We can run in manual at a constant speed, okay. But we try and go to control, the pump will...
I have been asked to fit an external tap at a mental health facility to enable the external paths to be hosed down. What form of back syphoning measure is sufficient for this installation?
Can anyone explain this? I had a shower professionally istalled in my en-suite a few weeks ago, as art of a full refurb. We use the shower from time to time but not daily. I was sitting downstairs alone in the house when I heard a loud bang and went up to find the fixed glass of the shower...
Hello im a new member and hoping for some experienced advise
Im a plumber with 12 years experianced and have recently started working in a super luxury 35 story tower block in london all very expensive
Anyway a prv on the hot water exploded the other day inside a riser cupboard and flooded...
Hi All, looking at getting a water boiler for our brewery and brewery taproom, we don't need central heating just need hot water for a small amount of cleaning in the brewery, bar and pizza kitchen.
Ive had a quote for supply and install (just push fit into water fittings, connect to gas) of...
Having a chat with colleagues on this one to decide on best route.
Existing 500L megaflo which does not provide sufficiant HW.
Cold water entering cools the hot way too quickly and consequently the 500L is good for about half that.
Coil is 54kw boiler is 80kw
Cylinder options…
The...
We are using a the rigid 65s pipe cutter for the smaller stuff but we have a load of 88.9mm x 2mm stainless coming up and was looking for a decent pipe cutter. Any suggestions?
Out of curiosity, how are hot and cold water systems designed for places like a hotel or gym with multiple bathrooms? I always find these places have water gushing out of taps and you never have to wait for hot water.
My guess is hot and cold water tanks with pumps and secondary circulation...
Hi all,
my employer took on a new build property which was built for them last year. There are 4x 480KW Ideal condensing boilers installed to serve a district heating network serving approx. 560 student apartments.
Due to a lack of decent control, these boilers are achieving a seasonal...
Hi,
I will try to explain best I can, please bare in mind I am currently in a learning stage so just trying to understand the process behind things.
A building with three floors and 69 rooms. How do you work out the pressure needed on the hot water system? I’m sure there is a calculation to...
Hi all,
Hope all are well.
I’m in the early stages of renovating an industrial unit. The fit out is to have 7/8 commercial kitchens, these kitchens will have reasonable output, i.e. high street takeaway in terms of their demand.
The unit has 3 bar of pressure and 25 litres a minute of water...
Hi,
I'm a sparky. We are installing a couple of standard S plan control systems for a couple of new domestic sized system boilers in a residential care home. We also look after the fire alarm here.
The client has just had a new tanked gas supply installed on site to supply these boilers which...
Looking at replacing a stainless steel welded 90 metre water system in press fit. Its going to cost about £18k in Mapress but I have seen M-Press are alot cheaper on their fittings. Has anyone got any experience with M-press 89mm fittings. Just wondering if they are cheap for a reason.
I have a WB 30i system boiler with a Honeywell programmable roomstat in the hallway and a cylinder stat.
With a new double glazed porch, cavity wall insulation and topped-up loft-felt the house must has a high efficiency rating. But….we now live in the ‘Sunroom’ off the hallway and this has DG...
My local rugby club are having intermittent pressure drop problems with their showers. I’ve done quite a lot of domestic plumbing but need advice on this. The system is set up with 4 large hot water storage tanks, there are 4 pumps each which have a flow sensors on them. There are 10 showers...
Hi all, hope everyone is keeping well.
I was wondering if anyone can help me work out the best boiler to cover this: -
1.) Modulation ratio of 9:1 or higher.
2.) BMS controlled modulation via 0-10v signal.
3.) BMS feedback re boiler modulation via 0-10v signal.
4.) A reliable boiler too...
Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website. For the best site experience please disable your AdBlocker.