Good morning, was hoping someone could tell me the minimum height the header tank needs to be above the hot water (indirect) cylinder. Many thanks in anticipation. Sam
Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws
- Thread starter Sam Whitmore
- Start date
Not sure if its a minimum height above your cylinder would be more thinking taps and shower height .
The higher the better pressure at your taps etc
The higher the better pressure at your taps etc
Currently the header tank is in the loft but I've plans to use that space and wanted to relocate the header tank which re-fills the central heating system to just above the hot water cylinder
Sorry misread your question yes their is i think its pump to water level if i recall depends on what pump you have
Have the system converted to a seal one, it really is beneficial to loose the F&E altogether Sam.
& you could then extend the heating up into the loft.
& you could then extend the heating up into the loft.
Hi Chris, for various reasons, cost being one I'd like to continue with an open vented system. I've about a gap of a metre above the cylinder but wasn't sure the header tank needed to be higher.
Not sure that cost would be dramatically different to labour for moving existing
There is no real height requirement other than it must provide enough head pressure to allow the top most parts of the system to fill with water, which would presumable be the upstairs rads not the cylinder coil.
The issue is more to do with the correct pipework design & installation, all intended to keep as much of the system under positive pressure when the pump is running at the same time ensuring that when it starts up water is not pushed out from the safety open vent pipe into the cistern. Lastly as much as possible of the extra water created when the system is heated remains in the within the cold feed as water moving up into the cistern when hot & then back into the circulating water when cold would introduce oxygen & promote corrosion.
The issue is more to do with the correct pipework design & installation, all intended to keep as much of the system under positive pressure when the pump is running at the same time ensuring that when it starts up water is not pushed out from the safety open vent pipe into the cistern. Lastly as much as possible of the extra water created when the system is heated remains in the within the cold feed as water moving up into the cistern when hot & then back into the circulating water when cold would introduce oxygen & promote corrosion.
The oversized combined feed & vents can be useful in this but we would need to see your present system set up to advise further.
F&E tank supposed to be at least a metre above the highest circuits in your heating system.
But extra long feed pipe is often better to ensure less air ingress into system.
But it depends on how it is all piped on your system.
You would be best to have your heating system sealed if it is gas or oil system.
There is very little cost to this normally.
The system will need to be sound though, - no slight weeps anywhere and radiator valves all with proper sealing glands, so no pressure loss
But extra long feed pipe is often better to ensure less air ingress into system.
But it depends on how it is all piped on your system.
You would be best to have your heating system sealed if it is gas or oil system.
There is very little cost to this normally.
The system will need to be sound though, - no slight weeps anywhere and radiator valves all with proper sealing glands, so no pressure loss
Rob Foster
Esteemed
Look, what you should consider is how high you can locate your tank...not how low ..done the odd one over the years at min. spec height and they worked but the performance really was rubbish
in my opinion...or just rip it all out and go unvented
chking
in my opinion...or just rip it all out and go unvented
chking
Rob Foster
Esteemed
Hiya Yd
he said at the beginning it was the high level cold water then it got mixed up ....(as usual) into the f&e ..I wonder which one it might be ...happy days my Sunday dinner is wafting up to my workshop ...beef today
Rob Foster aka centralheatking
W
Welder
Rob Foster
Esteemed
We must meet up for a beer I think..email on our commercial
address [email protected] ....often leave Lancashire and visit your province...in Wetherby in two weeks time
centralheatking
Rob Foster
Esteemed
Official Sponsors of Plumbers Talk
Similar plumbing topics
- Question
- Question
- Question
- Question
- Question
- Question
- Question
- Question
We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.
