What we all working on this week ?

[king of pipes]

I have a insurance job to try and rescue a poorly installed quad shower the customer wants to save the tiling if possible and has a few spare so fingers crossed it may work , the loss adjuster allowed em £1500 that will just about cover materials. Kop

 

[Scott_D]

legionella re work / dead legs in schools

I got loads of scrap from Royal Mail building a few years back removing dead legs on MCW 😀
[automerge]1596035022[/automerge]
Some one asked about these angle brackets for flue bracketed a while back. Screwfix sell them £8 for 10

 

[SimonG]

Home for the next two weeks, sorting out some pee poor work.

And yes the speedfit was cut with a hacksaw!!
[automerge]1596198249[/automerge]
Oh and them walls are freshly skimmed 🤣🤣🤣

 

[Scott_D]

Repipe for UFH manifold

 

[king of pipes]

Home for the next two weeks, sorting out some pee poor work.

And yes the speedfit was cut with a hacksaw!!
[automerge]1596198249[/automerge]
Oh and them walls are freshly skimmed 🤣🤣🤣

Wow who the ---- did that pile of pony good luck mate the phrase is you can't polish a turd but you can sprinkle it with glitter 😂😂. Kop
[automerge]1596214373[/automerge]
Finally on the home straight god I've put some hours in here 🤣 must be getting slow in me old age . Have a good weekend chaps regards Kop

 

[SimonG]

Wow who the ---- did that pile of pony good luck mate the phrase is you can't polish a turd but you can sprinkle it with glitter 😂😂. Kop
[automerge]1596214373[/automerge]
Finally on the home straight god I've put some hours in here 🤣 must be getting slow in me old age . Have a good weekend chaps regards Kop

Only had a couple hours this afternoon at it. Stripped all the previous crap out and got a bit of copper in.

 

[king of pipes]

Only had a couple hours this afternoon at it. Stripped all the previous crap out and got a bit of copper in.

Looks better already Simon 😉

 

[Harvest Fields]

I’m here for the weekend.

Popcorn anyone

 

[SimonG]

Well, just taken out a compression valve that would have been behind the shower valve, on speedfit, no inserts. 🤣🤣🤣🤣

 

[ShaunCorbs]

Well, just taken out a compression valve that would have been behind the shower valve, on speedfit, no inserts. 🤣🤣🤣🤣

😀 I think next time you see him you should remove his tooks and just leave him a hammer and screwdriver

 

[king of pipes]

Well, just taken out a compression valve that would have been behind the shower valve, on speedfit, no inserts. 🤣🤣🤣🤣

Oh dear a little bit of knowledge can be dangerous mate at least you found it . Kop

 

[ShaunCorbs]

😀 very expensive sinks

 

[Jim Goodenough]

😀 very expensive sinks

Did you install the whole shebang Shaun?

 

[ShaunCorbs]

Did you install the whole shebang Shaun?

Just the ply and the sink there football watchers / players seating 😀

 

[Jim Goodenough]

Just the ply and the sink there football watchers / players seating 😀

£500/ea (no water just gallons of sanitizer?)??

 

[ShaunCorbs]

£500/ea (no water just gallons of sanitizer?)??

Close enough 550 plus and no will be piped up with blended and push taps

 

[Jim Goodenough]

Close enough 550 plus and no will be piped up with blended and push taps

Please update with more photos as and when....

 

[ShaunCorbs]

Please update with more photos as and when..

Yep will do 🙂 when I get time to go back 😀

 

[Aquarius]

Just the ply and the sink there football watchers / players seating 😀

Thought it was a bit ott for a smokers shelter 😂

 

[Jim Goodenough]

1st fixing in a bungalow, this is one of 3 main pipe drops.

 

[ShaunCorbs]

Installing cast stacks in warm weather it’s not the best but looks good

 

[Aquarius]

Painting the house, so tedious and laborious 😫

 

[SimonG]

Answering phone, messages and texts. Today things have just gone mental.

Trying to finish a job off then to look at an air locked hot water system.

 

[Jim Goodenough]

Installing cast stacks in warm weather it’s not the best but looks good

From ladders or tower......?

How are the joints made?

 

[ShaunCorbs]

From ladders or tower....?

How are the joints made?

3 sec Ladder and pulley same as push fit but more of a pita as there really really tight to account for any defects in the casting

 

[Jim Goodenough]

Meant to add this photo yesterday.


2nd drop nearly done.

[automerge]1596735310[/automerge]

3 sec Ladder and pulley same as push fit but more of a pita as there really really tight to account for any defects in the casting

Pulley attached to ladders?
Plenty of silicone grease then?