As per the title can you fit a Drain Cock on Mains Water??
i have always fitted a "T" fitting after the stopcock and put a Type A drain cock in so once isolated the whole system can be drained but been told today this is wrong anyone care to add their thoughts??
Hello
I need to change the flow valve in my toilet, and have turned off mains
water supply outside my property and turned on all the cold taps but
the tank was still filling after 20 minutes.
Should I have turned on hot taps as well.
Hi, looking for some advice on what to do about my variable water pressure.
I have recently had a new boiler fitted, it's a combi boiler fitted by British gas, the old boiler was a hot water tank and gravity feed system.
Once the new system was fitted I noticed that the hot water flow was...
Okay so you may have seen my previous post regards to this but I'll just enlighten again.
Now I've never installed anything this big and just got my commercial ticket so bare with me. If I sound a bit amateur rest assured I will not start job till I'm 100% confident.
Got a 8 bedroom house...
Hi all,
current job to replace old lead incoming mains for 25mm poly pipe, from the meter in front garden to kitchen at back of house, 3 bed semi with a combi boiler,
!question! do I need to include a double check valve on the incoming mains water valve arrangement.
many thanks
Now then fellas, just signed up as im abit stuck with a job at a tenants this afternoon, for a month or so since they had their new boiler fitted (Vallient ecotec +824) all the cold taps in the property hammer when theyre opened , which in turn causes the hot taps to kettle up and begin to pass...
Hi All,
To cut a long story short I've a Ideal istor boiler I've posted abotu previously. Its an unvented cylinder all in one boiler. Bad reputation but mine has been good over the last 2.5 years. I had a new mains fitted a year back-ish and hoped for better flow rates. This didn't happen...
Hi All,
I'm looking into ways of increasing the supply flow rate, so that my shower doesn't reduce to a trickle when other outlets are used at the same time.
The mains supply is in 15mm (what I can see of it anyway). My question is - will getting the provider to upgrade this to a bigger pipe...
I have read through all posts about lead mains replacement to MDPE.
To get my head round it can any plumbers give a guide to how it's done. I've seen parts of it done once as an apprentice.
In my case there is the drive way. So you'd dig up the drive way from the boundary stop valve to the...
Hello,
I was hoping someone could answer a query that has puzzled me for a while and nobody has been able to help all that much. I have a new mains water supply coming into the basement which has replaced the old lead version. This new connection is instantly greeted by a pressure reducing...
Hello everybody. I've been asked to fit a mains water filter, God knows why when we live in one the best quality water areas in the country but ours is not to reason why.
can anyone suggest a mains water filter that can be fitted under the kitchen sink without too much bother. I would ideally...
I a house with low pressure water a Monsoon Pumb can be used to increase water flow at taps on demand is there a similar method I can setup for a large rainwater tank with the extra complication of a mains water connection if the water butt is empty! I can place the tank in a shed for protection...
Hello
Experience: DIY plumbing.
i have installed a couple of cisterns and used 15mm compression to the plastic cistern connection, never had a leak. The ends of the pipes appears to be 'chamfered' if that's the correct term, for an olive, not flat like a tap connection, hence the logic...
I went to a job today of a lady complaining about the hot and cold water pressure.. She said every now and then both hot and cold stops completely then comes back on.
Naturally I think it's a gravity system and either a ballvalve issue or an air lock of some sort, or maybe a pump.
I get there...
hi, please excuse any ignorance on my part that this question may throw up.
my lead metal mains pipe enters the house and looks a respectable 3/4" outside diameter but within 6 inches it is reduced to 15mm copper to pass though the stopcock. this then passes through the water meter using 15mm...
Hi there. Any help appreciated with this one.
I've had no hot water coming from the kitchen mixer tap, so I adjusted the cylinder mechanism in the tap so that hot water flowed OK.
However, when I turned the mains water back on, the overflow pipe outside began to gush water.
Looking at the...
Hi guys. Never done this before. Have an unvented hot water cylinder to go up in a loft conversion and think I'll have to dig from the mains stopcock as the existing is old lead (7 1/2LB) 15mm and needs to be 22mm and feed back into the downstairs kitchen and up into the loft, connecting to...
Hi all.
Bumped into a guy who worked for a water supply company the other day and he mentioned that the supply company has a duty to be giving at least 10 litres per minute to a property. Is this true and if so is it true for all of the UK?
regards, chris
Evening folks, I'm about to commence work on a 8 bed new build dwelling, the custard has just emailed me, asking if i know anything about how the incoming mains from road( about 130 metre run). Is it a requirement before or after Anglian water connect it in the road? I've carried out...
I was hoping to get a professional opinion regarding whether or not a booster pump (such as a Stuart Turner 'Flomate') would do what I want it to do.
At present the flow rate in our house isn't terrible - about 10 litres per minute at its best - but that doesn't seem to go far if more than one...