T
Throttledwife
Wish i had taken pics of the boiler we changed in my house..you lot woulda loved it..
Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws
HALL of SHAME PHOTo`s
- Thread starter Barry98
- Start date
-
- Tags
- None
View the thread, titled "HALL of SHAME PHOTo`s" which is posted in UK Plumbers Forums on UK Plumbers Forums.
See anything wrong?
G
Gray0689
Agree service valve on vent side lol love to see it implode lol
And that lazy couldn't solder a bend on
And that lazy couldn't solder a bend on
R
REDSAW
the cylinder fell over?
^^ you joke Bod but i went to a job where some numpty had fitted a surry flange and replaced the vent pipe with a auto air vent and a 2 bar pump which must of pumped back and belled out the bottom of the cylinder. When i took it out a 48x18 cylinder was 6 inch"s out of level the only thing that saved it was it went backwards against a wall and not out of the door
B
Barry98
Nothing I see amazes me no more
B
Barry98
but its always been like that
D
Dotty
Probably a sparkie. Suited him and no one else!
M
Mike Jackson
Finished Fitting a new combi to a property on Monday and no matter what I tried I couldn't get any heat to the drops. With all the rads bar the drops turned off the return to the boiler was red hot but none of the rads were getting hot. This led me to believe that there must be some sort of bypass on the system. I Lifted a few boards and checked the return and it was stone cold as far as the bathroom. The only place there could be a problem was under the tiled bathroom floor.
I returned today with a borescope and struck lucky on the third hole I drilled in the ceiling. I found this.
Bypass by Mike Jackson1, on Flickr
No wonder the drops wouldn't heat up.
I returned today with a borescope and struck lucky on the third hole I drilled in the ceiling. I found this.
Bypass by Mike Jackson1, on Flickr
No wonder the drops wouldn't heat up.
B
Barry98
Ooooooooooooo bad bad bypass
K
kay-jay
Finished Fitting a new combi to a property on Monday and no matter what I tried I couldn't get any heat to the drops. With all the rads bar the drops turned off the return to the boiler was red hot but none of the rads were getting hot. This led me to believe that there must be some sort of bypass on the system. I Lifted a few boards and checked the return and it was stone cold as far as the bathroom. The only place there could be a problem was under the tiled bathroom floor.
I returned today with a borescope and struck lucky on the third hole I drilled in the ceiling. I found this.
Bypass by Mike Jackson1, on Flickr
No wonder the drops wouldn't heat up.
That's some drill bit to drill big oblong holes 😀
Sent from my GT-I9100 using Tapatalk 2
Yeah, looks good. Where can I get one of those drills. Dead handy 😉
Bad bypass. Why would someone do that!?
M
Mike Jackson
I couldn't figure out a reason other than someone didn't have a clue what they were doing. I'm not sure why the previous plumbers that have been out and flushed the system several times didn't do a bit more investigation and figure out the problem. I was glad to as it gave me an excuse to buy a new toy, oops sorry I mean tool.
Nipped back this morning to finish off the pugging up outside and the customer greeted me with a big grin, it was the first time he had been warm downstairs in the winter since he moved in two years ago.
I had the same problem a couple months ago - a heating system from the 1960s had a 3/4" one pipe loop from the flow to the return immediately after the first rad.
I also fell for it, as the people were new owners & system hadn't been tested until I had been replacing some rads & pipework. Big relief when I found the bypass which had been to feed 2 previous rads on a 1 pipe loop (which would have always acted as a bypass). Felt good that I was the only guy that sorted it in 40 + years! :smile:
Some "plumbers" make the mistake of thinking a 2 pipe system must have both pipes joined for a loop, especially when they are capping off a rad for good & it is the last on a circuit.
I also fell for it, as the people were new owners & system hadn't been tested until I had been replacing some rads & pipework. Big relief when I found the bypass which had been to feed 2 previous rads on a 1 pipe loop (which would have always acted as a bypass). Felt good that I was the only guy that sorted it in 40 + years! :smile:
Some "plumbers" make the mistake of thinking a 2 pipe system must have both pipes joined for a loop, especially when they are capping off a rad for good & it is the last on a circuit.
Last edited:
Also, the plastic fitting is too close to the cylinder. And it doesn't look like there's 450mm (min) to the vent pipe going up. Can't see the rise either.
Alex if you look good on that photo is not about the plastick fitting and the 450mm !!!! Is to do with the 22mm service valve mate !!!
To MJ : this looks to me as a ch return teed to the primary return
To MJ : this looks to me as a ch return teed to the primary return
Last edited:
J
jase158
10 points for the first to get all the problems
G
Gray0689
10 points to me as its all crap ;-)
T
tamz
I'll name that tune in 1 to save typing.
Fitted by a idiot. Rip it out and start again.
T
tamz
You beat me to it Alex.........your points :lol:
G
Gray0689
Lol think we will split the points tamz
Jase you owe us 5 each lol
Jase you owe us 5 each lol
J
jase158
umm, everything and all of it dont count, no where near right.... I want to see if you spot the not so obvious aswell as the obvious.
Also forgot to take a picture, but overflow from f and e went into the cwsc
Also forgot to take a picture, but overflow from f and e went into the cwsc
B
Billy Bob Bob
as said its all crap,wonder how long before that 2.5 t+e melts behind the return
K
kay-jay
Home made wonder i saw yesterday made me chuckle
And the other end
Voila ....a wonderful home made douche spray.
Sent from my GT-I9100 using Tapatalk 2
And the other end
Voila ....a wonderful home made douche spray.
Sent from my GT-I9100 using Tapatalk 2
O
on31ll
is it the flexis ?
R
Ray Stafford
Official Sponsors of Plumbers Talk
Reply to the thread, titled "HALL of SHAME PHOTo`s" which is posted in UK Plumbers Forums on Plumbers Forums.
Similar plumbing topics
We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.
