What we all working on this week ?

[king of pipes]

I have a insurance job to try and rescue a poorly installed quad shower the customer wants to save the tiling if possible and has a few spare so fingers crossed it may work , the loss adjuster allowed em £1500 that will just about cover materials. Kop

 

[SimonG]

Playing with my new toy this morning. It's a beast.

 

[Harvest Fields]

Playing with my new toy this morning. It's a beast.

Is that a kango? Not seen one in a while

 

[SimonG]

Toolstations best. Einhell £120.00. It wont get a lot of use, but by does it beat the sds drill 😀

 

[Aquarius]

Playing with my new toy this morning. It's a beast.

Mmmmmmmmmmmmmm nice !!!!! (Bloody 20 characters thing)

 

[Harvest Fields]

I have both. Yes the are good, saved me a couple of times. Worth getting a set for £10ish

Where did you get them from? Got a link. I can only see 15mm

 

[ShaunCorbs]

BES.co.uk | Next Day Delivery On 15,000 + Plumbing Supplies

www.bes.co.uk

 

[Scott_D]

Williams and co for mine, also eBay

 

[Harvest Fields]

Thanks both. It’s appreciated.

 

[king of pipes]

Kitchen sink swap today it was a total pig to do, getting it out was the easy bit the worktop needed cutting out bigger and the cabinets needed trimming out, i did like the way the tap fixed to the sink looked tidy once compleate. Kop

 

[Harvest Fields]

Looks nice mate. Definitely worth the effort.

 

[SimonG]

Kitchen sink swap today it was a total pig to do, getting it out was the easy bit the worktop needed cutting out bigger and the cabinets needed trimming out, i did like the way the tap fixed to the sink looked tidy once compleate. Kop

Doing an outside tap this morning and asked me to tighten the tap whilst there. Same type of fitting. Hadnt seen one before.

 

[king of pipes]

Bath to shower upgrade new vanity and digital shower now done apart from the 1m shower glass which I am having trouble getting ordered 3 weeks ago still not here grrrrr. Kop

 

[ShaunCorbs]

Fml joiner who can’t build a square wall it’s out 4” cross and 11/2” in 800mm (width of the tray)

 

[Harvest Fields]

Get out of it. You cut your board wonky😉😉

 

[ShaunCorbs]

Get out of it. You cut your board wonky😉😉

😀 hope not traced round the shower tray, knowing my luck lately your prob right
[automerge]1601394168[/automerge]
The floors sloping all directions so took some time but it’s level and solid

what’s the chances of it getting covered in plaster you think 😀

 

[SimonG]

Barrel finished at last.

 

[Aquarius]

Barrel finished at last.

It’s looking sharp Simon, is a kind of mixer tap/watering can?

 

[SimonG]

It’s looking sharp Simon, is a kind of mixer tap/watering can?

I took hot and cold through double check valves behind barrel, up through the 15mm gate valves for hot and cold taps and then t'd together in wall. 15mm comes out through bottom of watering can and then reduces to 10mm which I managed to direct down through the spout.

 

[Ben-gee]

Nice one! 👍
Bit more interesting to do than the usual, hard to price that sort of thing though, but I’m guessing an existing customer so do job then send bill?

 

[SimonG]

Nice one! 👍
Bit more interesting to do than the usual, hard to price that sort of thing though, but I’m guessing an existing customer so do job then send bill?

No new customer. Estimated day and half plus materials. Came in slightly under estimate. Customer pleased and already have to go and look at a couple of bathrooms through her recommendation.