Welcome to the forum. Although you can post in any forum, the USA forum is here in case of local regs or laws

fittings

  1. A

    Are expensive compression fittings worth it

    I need to add a two port valve to an existing system. As part of this job I need to add a few compression fittings. Wanted to ask those more experienced is it worthwhile buying (as an example) a Prestex (Pegler) 28mm equal T for £12.80 vs cheaper non-brand at £8.05? Is there real any...
  2. N

    Will Pex Hose With SharkBite Fittings Work on 1/2" Copper Pipe ??

    Have an Inline Shut Off Valve with Compression Fittings that has developed a Leak.. The Valve actually serves No Useful purpose.. Because of limited access and no real wiggle room.. Could I Safely use a piece of Pex Hose and SharkBite Fittings to Replace the Valve completely ??
  3. R

    Tightening of standard compression fittings

    Hi ya guys, im trying to improve my way of tightening compression fittings to copper and plastic pipes (using inserts or liners in the case of plastic). I usually in the case of copper push on nut and olive over tubing, add uni-white squeese by hand and then tighten with spanners for about 4...
  4. C

    Dual Flush Valve Fittings

    I'm in the process of trying to replace a leaking flush valve with a Flomasta Dual flush Fill valve kit. The problem I've got is trying to get the flush pipe connected into the base of the valve. The existing flush pipe is marginally too small, but might be OK with a suitable gasket but I'm not...
  5. R

    press fit fittings suppliers

    looking to stock up on m press fittings wheres the best place to get them ?
  6. I

    MuPVC waste pipe should NOT be solvent welded to ABS waste fittings. Why?

    In reality though, it's done all the time. Most don't realise it shouldn't be done and the reasons why. So why? What are the potential problems and the likelihood of those problems happening over time if an MuPVC to ABS joint is made and brought into service for hot and cold drainage? Is...
  7. Uheat – Jake

    MLCP Pipe & Press Fittings

    We stock a wide range of MLCP Pipe and Fittings and are constantly speaking to plumbers about MLCP and how it can reduce installation times and also reduce material costs, but we'd like to know why you use MLCP, or if you still prefer Copper or Pushfit? So what are peoples opinions on MLCP?
  8. B

    Copper pipe cutter for plastic fittings

    Hello, I have a traditional “disc” type cutter that you wind down onto the copper pipe but I’m told it’s best to have a cutter or “slice” that leaves a chambered edge on the copper pipe so it clears the plastic fitting O ring. Can anyone recommend the best cutter for 22mm and 28mm copper pipe...
  9. J

    philmac fittings blowing off.

    hi folks, I have a problem with a fairly new housing project. I have philmac pipe 25mm connected below sinks onto a philmac union and they keep blowing off, I have had scottish water to the properties who have tested the pressure which is sitting at 5 bar, pipework does not have any clips below...
  10. T

    Identification of toilet cistern fittings

    Hi P{lease can anyone identify which manufacturer and model is shown in the photos. The flushing valve is leaking water into the bowl and suggestions for replacement will also be helpful Thanks
  11. Plumbase Spares

    How Bristan EasyFit taps simplify kitchen fittings!

    Homeowners always keep up with the latest trends in kitchen refurbishments and ways to cut down costs. So, plumbers and installers need to ensure they can offer their customers competitive quotes, whilst maintaining margins by cutting down installation times. On average, replacing a kitchen...
  12. B

    damaged tile on shower fittings

    Hi all. Any idea on the best way to repair this quite visible chip around the shower tap fitting? Is it a matter of trying replacing it? what is the best way to solve the issue avoiding damage to the other tiles and to the shower screen (frameless one with hinges attached to the adjacent tiles)...
  13. D

    Old Hep fittings?

    Hi, Thanks in advance for any advice! I'm helping a friend with his water pipes, and I'm wondering about the grey fitting in the picture. We just bought some HepKeys which successfully dismounted the white fittings, and I'm wondering if the keys would also dismount the grey fitting, as I'm...
  14. M

    MLCP Pipe & fittings - press fit

    Hi After a recent job needing some parts I’m thinking of using this stuff on a job that’s a I start soon. I’ve a quick look online though and not that many places seem to sell much of it. For those who use it already, what manufacturer do you use and where do you buy it from? Cheers Martin
  15. Plumbase Spares

    Exclusive Endfeed Fittings offer - 24 HOURS ONLY

    Consisting of quality Endfeed fittings, that are WRAS approved and manufactured to EN1254-1, this pack provides all the fittings you need for standard water and gas application in an easy to handle and store bucket. CLICK HERE
  16. L

    MDPE pipe and fittings, are all equal? What durable brands to buy?

    Dear All, Whenever possible I aim to buy the correct quality product the first time round. Plumbing labour and water damage is expensive, thus, very happy to pay quite a bit more for materials provided it is needed to ensure a lasting product over time. Your advice will be much appreciated...
  17. D

    New Polymax fittings from Polypipe

    Has anyone used the new Polymax fittings from Polypipe? I've just ordered their free sample pack to try them out. From photos, they look almost identical to Hep20.
  18. E

    Least Bulky Plastic Fittings

    Hello, I want to extend a radiator using either PEX or HEP20 pipe, which type of pipe has the least bulky fittings as I need to fit under floorboards.
  19. gingalig

    Press fittings gas mechanical or not

    Hi I spoke to gas safe today as wanted clarification that it was or was not considered a mechanical fitting using press fittings on gas pipework, the response was that it was to new to call and i would need to speak to the manufacturere, long story short and a lot of call waitiing and i didnt...
  20. H

    Mixing metals on compression fittings

    Annoyingly I have used a copper nut on a steel isolation valve and the corresponding steel nut on a compression copper fitting (15mm). Should I dismantle and redo? I will have to buy a length of plastic pipe and new olives as well as drain system. Or will it be OK?

We recommend City Plumbing Supplies, BES, and Plumbing Superstore for all plumbing supplies.

Featured Content

Back
Top