Good afternoon, we have a Potterton Performa 30HE and have got a problem of having no hot water in the kitchen. The boiler is in the kitchen and feeds the bathroom first and then comes back down to the kitchen, the hot water is ok in the bathroom but the tap needs to be running virtually full...
Hi, I'm looking for recommendations for good quality taps. Ones that will last. My kitchen mixer-tap is leaking after just 3 years, and it wasn't cheap.
I need a low pressure tap, as my hot water is gravity-fed. Monobloc, ideally 2 levers.
Recommendations on good brands to look for would be...
Hi, a plumber has been out to my rental property as my tenant reported a blockage causing water to flow back from the washing machine into the dish washer. Both were disconnected and their drainage hoses cleared out but the plumber advises that there is more of a blockage further down the waste...
Hi All,
Having a problem whereby we aren't getting any water from our taps except the cold water from the kitchen which is working fine.
Going to get a plumber round to look, but any idea on what the likely cause is? My assumption is that there is a problem with the tank in the loft and I...
I purchased a tow aerators for my kitchen mixer tap now but neither will screw all the way up even with the rubber washer taken out, it leaves about a 3mm gap.
Any ideas on what I can do?
Another cheap chineese crap tap, customer has bought a kitchen tap with spray which also has a separate outlet which turns on/off, so both outlets turn off
The problem is when you let go of the spray or turn the other outlet off and the main control/temperature (on the bottom of the tap) is...
Cold water side works but hot suddenly stopped working.
I’ve checked that there are no leaking pipes. Any idea? I got it installed 1 month ago. Is it down to a poor installation???
Hi. I need to install a kitchen sink in a bathroom. I’d like to use a standard bathroom sink drain/stopper but the hole in the sink is too large. Is there some sort of oversized flange or similar I can use to reduce the size of the hole to accept the smaller drain? Thanks!
Okay so I went and purchased this nice Grohe Bau Curve Kitchen Mono Mixer Tap and I knew it came with 6mm bore flexi tails which was fine because I thought I'll just change them with 8mm bore flexi tails that I purchased at the same time.
When I tried to undo the preinstalled flexi tails from...
Hi
I was wondering if someone could please tell me how to connect the flex pipe from sink overflow drain in to waste trap below? It is the Cooke & Lewis Waste Kit ‘B’
If I can add pictures then I can show?
Hi, I am a basic home DIYer with limited knowledge looking for some advice.
We have a sink in our utility that has a washing machine connected into the same pipes. The sink is constantly getting backed up. Worse when the washing machine is draining but will start to back up with the tap just...
hi i have a dripping tap at the kitchen sink but the isolation valve will not move, i have tried wd40 on it but it wont budge.
any advice on what to do with it please?
also i live in a maisonette and there is no stop tap thing under the sink- any ideas where i would / could find the tap to turn...
Hello folks.
I have just changed the kitchen tap and now there's no hot water in the kitchen or bathroom. I've tried pushing out any airlock by connecting the hot water to the mains cold via the washing machine connection,to no actual.
Everything worked fine before. I've a Worcester combi...
Trying to find a replacement for the below sink strainer and completely stumped! all the ones i see dont have the black base bit on and dont seem to work! any ideas for a replacement or the specific name of this type? Thank you!
Hi,
My kitchen sink trap/waste is leaky a bit from the connection highlighted below. It mainly happens when there is pressure (when I fill up the sink and open it in one go), and the connection becomes a bit loose and water starts pouring out. I have tried tightening cap, but after a while it...
I have a quarter - turn Cold Water Kitchen Sink Tap that has a started dripping and i am trying to gain access to the washer/valve assembly and looking for advice as to where/how as cannot see any obvious screws on the main tap body and the small blue plastic insert does not seem to move...
Dear Sirs
I had a kitchen hot water hose which bursts this morning. This is a new connection for a new kitchen tap only a couple of months. The plumber installed a white connector (similar to the one remaining on the top) to the isolation valve but it bursts to somewhere (probably behind the...
I have a quarter turn cold water kitchen tap that has a slight drip and cannot see if the valve assembly is removed from the top? ---- there is a blue plastic cover in the top but does not seem to come off?.......... have photos of tap if anyone can help?.
Hi. I was
Wondering if anyone can help
I had a huge leak under my kitchen sink
And where the bowl sink kit goes onto the outside pipe/waste I just can’t get a seal, just doesn’t stay on.
Can see in video/pictures
Can anyone advice how I sort this out.
It’s almost like all of a sudden...
I cannot find supplier of the seal to stop the leak from underneath the
kitchen sink?
Does the seal have name?
Images
The leak is from the first compression joint underneath the sink.
Sketch of seal.
Not very good picture of seal.
Thanks.
Mike