Two boiler install:- PRV location. (Pictures)

[Dotty]

Harry lad, can you send a pm with your gsr details to gas man please, we'll get you into the private forum then.

 

[harrygashull]

Harry lad, can you send a pm with your gsr details to gas man please, we'll get you into the private forum then.

Aye, no problemo.

 

[harrygashull]

All up and running! What do you all think?



https://m.facebook.com/MCSHeating/p...6908248382352/?type=3&source=54&ref=bookmarks


https://m.facebook.com/photo.php?fb...207520000.1449856681.&source=54&ref=bookmarks

 

[quality]

Good job that sir

 

[ShaunCorbs]

very good effort harry and you should be proud couple of niggles for me personally

gas pipe would of liked it closer to the wall and the use or musson rings as dont like clip spaces (too many of them looks like 3 - 4)

no drain offs on return pipe work (bottom sets)

and blow off would of liked a set

but thats me and im picky 😀

 

[harrygashull]

very good effort harry and you should be proud couple of niggles for me personally

gas pipe would of liked it closer to the wall and the use or musson rings as dont like clip spaces (too many of them looks like 3 - 4)

no drain offs on return pipe work (bottom sets)

and blow off would of liked a set

but thats me and im picky 😀

There is a drain off hiding at the bootom of the three gate valves on the return 😉 and there is also one on the return from the cylinder.

I agree about the clips however it was what was to hand at the time... Bould have been nice to use proper standoff clips but time wasnt permitting.

Im going back next week to flush and put inhibitor in🙂

 

[harrygashull]

Bit clearer on that lol

https://m.facebook.com/photo.php?fb...207520000.1449859260.&source=54&ref=bookmarks

 

[ShaunCorbs]

There is a drain off hiding at the bootom of the three gate valves on the return 😉 and there is also one on the return from the cylinder.

I agree about the clips however it was what was to hand at the time... Bould have been nice to use proper standoff clips but time wasnt permitting.

Im going back next week to flush and put inhibitor in🙂

you mean the lockshield valve 😀

and yes but food for thought on the next one (were allways improving)

but good job on the 28 bending

 

[harrygashull]

you mean the lockshield valve 😀

and yes but food for thought on the next one (were allways improving)

but good job on the 28 bending

Lock shield valve on there because I don't trust a drain off when flushing mains pressure haha

 

[ShaunCorbs]

Lock shield valve on there because I don't trust a drain off when flushing mains pressure haha

understand but whats why you put dedicated level valves in for flushing but fair enough as ive said before each to there own

 

[AWheating]

Just needed some Munson rings to help with the levels and wider spacing otherwise it looks good. Good look with the lagging 🙂

 

[harrygashull]

Just needed some Munson rings to help with the levels and wider spacing otherwise it looks good. Good look with the lagging 🙂

Armaflex me thinks?

 

[ShaunCorbs]

Armaflex me thinks?

yes very good inso

 

[gassafe]

must be a solder shortage in your area 😉

 

[harrygashull]

must be a solder shortage in your area 😉

Got 3 rolls to last me the next 20 years. 😉

Lol

Not really, I just try not to chrome all of the pipes. 😉

 

[Toddyplumb]

Im sure Worcester do a pipe layout for coupling 2 boilers together showing where all the safety devices and NRVs are to be positioned .

 

[harrygashull]

https://www.facebook.com/TradesmenE...6280?comment_id=1664388553847139&notif_t=like