twin boiler install - this cant be right can it??

[CChris]

Will have to leave the trv head off test until tomorrow as the kids are asleep and as we don't have carpet down in various areas yet Im likely to wake them clamping around. If they wake up at their usual 5am I'll give it a whirl then! Lol.

Heads come off no problem though so easy enough to do when I have the time. Got photos on the phone so will try and upload, but no pc to make it easy as we're still unpacking after moving back into the home after the building works.

 

[CChris]

In another stroke of genius it appears that the valve to the underfloor heating hasn't been wired in. It was permanently closed. Ffs I'm off to bed with a duvet and the lot shut off until the morning.

Thanks for the help folks. Will let you know how I get on.

 

[CChris]

Pictures and layout diagram as requested.

To be fair the plumber has been a pretty good guy, and has helped out with a lot of other issues which the main builder seemed to want to sweep under the carpet and hide away from me, so Im not wanting to fall out with the guy if there is anything obviously wrong, just looking for second opinions and dont want to make a mountain out of a molehill with the guy.

He called last night after I dropped him a text about the rads not warming up for the kids, and I advised that once ive loosened the collars on the TRV's a little, then things warm up - so it could be overly agressive TRV's causing part of the issue is my thought (which are being swapped when the evohome goes in anyway). The wiring in of the valve to the underfloor is down to the spark, so not attributing this to the plumber.

Anyway, heres the layout and pics - from my amateur untrained eye there doesnt seem to be anything amiss, and plumber advised offset(?) Tees rather than straight tees for the boilers would solve the reverse flow issue?

Thanks again for all the help, it is appreciated.

 

[Mike Jackson]

That layout is just screaming reverse circulation to the heating with the configuration of the returns.

 

[CChris]

That layout is just screaming reverse circulation to the heating with the configuration of the returns.

Can you explain this please? I know a bit, but dont profess to know it all, and dont want to come across that way when talking to the plumber. But any description of the problem would help - thanks 🙂

Im guessing its something to do with the returns from the HW tank and underfloor flowing into the return of the heating circuit. Would this be possible if the valve to the heating were shut at the flow end?

 

[CChris]

I know its replying to my own thread, again, but am I missing a boiler bypass here? if all four electronic zone valves are shut, I see no route to discharge the residual heat. Or am I missing something obvious as a novice?

EDIT: found the following in the installation guide for the boilers:

"However, if the system employs thermostatic radiator valves on all radiators, or two port valves, then a bypass circuit must be fitted with an automatic bypass valve to ensure a flow of water should all valves be in the closed position."

AND

"Systems incorporating zone valves which could completely cut off the flow through the system must also include a bypass."

As I have TRVs on all rads, and zone valves which could cut off the flow in all directions, Im assuming this applies to me and a bypass needs to be fitted?

 

[tolly]

That Primary flow looks 28mm to me, not 35mm like you've written in the pictures?

 

[ShaunCorbs]

not too bad install a few mistakes and tolly is right its 28mm

 

[CChris]

Can you advise on the "mistakes"?

Had the underfloor on for 4 hours now and it's not even thinking about getting warm. Flow pipe to the manifold is hot, return is stone cold. Manifold is warm, two flow pipes to the kitchen zone are also warm, but their respective returns are stone cold. Do the little things in the top of the manifold signify flow rate through those pipes? If so, there's no flow through them.

Yep you are right it's 28mm not 35. Could the 22mm take the theoretical 60kw from these two boilers?

 

[Chalked]

Needs check valves on return. The boilers will develop a pump flow fault, as it will not get a pressure increase on strt up. Caused by one boiler reverse circulating through another..

 

[ShaunCorbs]

Can you advise on the "mistakes"?

Had the underfloor on for 4 hours now and it's not even thinking about getting warm. Flow pipe to the manifold is hot, return is stone cold. Manifold is warm, two flow pipes to the kitchen zone are also warm, but their respective returns are stone cold. Do the little things in the top of the manifold signify flow rate through those pipes? If so, there's no flow through them.

Yep you are right it's 28mm not 35. Could the 22mm take the theoretical 60kw from these two boilers?

the pumps working on the under floor systems? and could you post a pic up as it sounds like a valve is shut/not open full if you have heat by the manifold

 

[buckley plumb]

could need bleeding all air out.

 

[CChris]

Here's the manifold etc. I believe one issue was the zone valve not being wired in for the underfloor heating. It was mostly shut, so very little flow to the manifold, but enough to get the flow pipe hot.

Manually set this to open and flow to the manifold is now fine.

Pump on the manifold appears to be working fine.

I'm only trying to heat one of the two zones controlled by this manifold, that's fed by the two pipes on the right.

I can feel the two pipes get warm, but flow meters on the top only ever show one of them moving, up to about 2l/m the other doesn't budge.

I tested putting the other zone on so that the other 3 pipes were in action, their flow meters didn't move either. Only ever the second one from the right (which can be seen in the picture).

The manifold itself on the flow side got very hot. I'd say not far off the temp of the flow pipe from the boiler. Thermostat on the left set just pas the 40. I assume this can't be right and I most certainly don't want to be sending 80 degree water into the under floor. So switched the lot off.

Any ideas on this one? I seem to be fighting numerous issues here.

 

[Nostrum]

This is why systems get commissioned, why hasn't it been done by the installer?

 

[chris watkins]

I hope you are holding a large retention on the Builder CChris cos you are going to need it to pay for the corrective works.

You have established that it is not working & not installed correctly so strongly recommend that you commission an independent consultant to prepare a report on what is wrong & what will be required to correct this.
I understand you want to find out yourself but with all due respect it is very complicated with all the component bits & how they will work or not together.

Just to answer a couple of your questions from earlier
1. You would need min of 35mm to shift 60kW @ Delta T 20deg C
2. The residual head pressure of the boiler pump in a 30kW boiler is less than 2 Metres this is not enough to overcome the resistance of the system fittings & pipework, hence why you don't have circulation. (you think it is bad now with outside temp of 15deg C just wait till the winter)

Please, I have seen enough of these Builders Plumber Jobs, get a pro in as soon as possible & you may want to sever your links with the installing plumber, I am sure his hart is in the right place but he is out of his depth on this one !!! More than likely he was almost forced to take it on by the builder or he wouldn't get any more work from them.

 

[CChris]

Appreciate the comments. Yes I do want to understand the issues myself but also appreciate that I'm not a plumber, so I'm in no way going to attempt to fix any issues myself or rely solely on answers from here to get things put right (although the advice is very much appreciated).

The under floor has been working. As has the heating. Both at different times and both in "manual" guise. I.e pumps plugged in and a single boiler on the wall etc.

I think the issues have arisen when it's come to sticking the second boiler on and connecting the lot up.

Yes there is still a decent chunk left to pay on the project of circa £30k plus another £4.5k retention, which I have zero intention of paying over until every single aspect has been demonstrated working.

For now the heating and hot water works in a fashion, so not the emergency it could be, but it will be inspected by another installer asap. Most likely the one I have had work on our office block.

You are almost certainly correct with the builder forcing the plumber to do it. This builder has very few contacts as he alienates almost every one he works with, and has been lucky not to wake with a horses head in his bed on this project if I'm honest. Had I not had some knowledge and another builder who has built rental properties for me in the past to call upon, he would have tried to slide some fantastic bodges past me. (Set a lintel too low, just cut the door frame down to suit.... as a minor example)

Really appreciate the input here guys, it is very helpful indeed. Hope I can return the favour somehow. If anyone is in the Chesterfield area and wants to have a look first hand and earn some beer tokens, feel free to drop me a message (apologies if this breaches any forum rules I am unaware of).

 

[stevetheplumber]

its badly undersized 22 isnt going to run even 15 radsyou are definitly going to need a low loss header and some bigger pumps

 

[CChris]

There are 19 rads on the 1st floor and 10 on the ground. Fed by a 22mm circuit to each, with the final connections to each rad being a mixture of 10mm or 15mm depending on their location either in the new or old part of the house (all pipe is new).


Are you suggesting I'm into having them lift the floor and replace all the 22mm run throughout the house?

 

[ShaunCorbs]

There are 19 rads on the 1st floor and 10 on the ground. Fed by a 22mm circuit to each, with the final connections to each rad being a mixture of 10mm or 15mm depending on their location either in the new or old part of the house (all pipe is new).


Are you suggesting I'm into having them lift the floor and replace all the 22mm run throughout the house?

maybe depends on how long the runs are/ how hes piped them

 

[CChris]

maybe depends on how long the runs are/ how hes piped them

I'd say longest run of 22mm is likely 30m or so to the last rad on the run.

As far as I'm aware it's 22mm flow, 22mm return and tees off in either 15mm or 10mm for each individual rad.

I guess all I can do as a basic test is to pop the tops off the trv's on all installed rads (20 out of the 29) and see if I can get them all belting hot in a not unreasonable length of time. If it can do that on one boiler then I'll probably be safe.

Worth adding that it is very unlikely I'll ever want them all on at the same time. Hence the evohome installation. It's more likely that only half the home would be heated at any point in time.

Still, I "should" be able to have them all belting hot at the same time.if I wanted, so it's no excuse for an undersized system if that turns out to be the case.